Search results

I've been quiet for a white now, but I can tell you all that I got near perfect video. I have done some work for a high demanding producer, and they are really satisfied with the result. Sadly my computer is to weak to prosess the footage right, but here is a IG clip from the upcoming project...

It has about 4 hours in the air. Yeti esc, and Tiger MN3515 motors. The bearings seems fine. Motors run smooth, and there is no play. Received new propellers today, so as soon as the rain stops, I'll start testing, and try to figure out what went wrong. The bad initialise theory sounds like it...

I doubt use of the cylic stick was the cause of this Crash, but Thanks anyway Sleepy. When you have the inirtalise problems Benjamin, is the status led normal?

Today my octo tipped over to the left and crashed at takeoff. It felt like the more throttle, the more the right side lifted. There was no mechanical flaws as I know. Yesterday it flew perfect at the same location. I did the calibration dance yesterday, and not today. The drone was transported...

Damn. How dit that happend? What was the cause?

What about the Vulcan Raven? Vulcan makes awsome frames, and this one is made for heavy lift.

Hi. I have been really busy, so I have not had much time flying. I still have some tuning to do, but I am getting better and better video. Jakub has been really helpful in the tuning prosess. (Remember that I am a total idiot when it comes to AM, but I am learning) I will post PIDs and video...

That is the video from the settings I did send you :) Can't wait to try out the changes you told me about. The wind was horrible, so in normal conditions, and with your changes I guess the result will be awsome :)

@SamurAchzar : Yep it certainly would. Will dial in the AM first as I really like the smooth encoder spring-like feeling, and then I will probably try the CP on it. When/if you release encoder firmware to the CP, I will probably go back to the CP for good. And keep in mind I am not done tuning...

Finally the rain stopped, but the wind did not... I took the chopper for a short flight. The wind was too hard and gusty for me daring to keep the bird flying for long, as it got tossed around really bad. I would normally never fly ,and certainly never do aerial video work in such conditions...

@saenzm : Coming from several quads and hexacopters I could not have been happyer. The frame is sturdy and rock solid. Build quality is superb. I have not had any vibration problems. Setting the gains with WKM "quad over quad" custom mix was easy, and done in one flight. In flight it feels quite...

Yep :) Will do it tomorrow. Im at work now. Not home until tomorrow morning.

Great tips @jakuban . Will do that :) I will try without the dampening plate first. I think it will be even more rigid without, and the Vulcan dampening plate is carrying batteries, landinggear and gimbal, and takes away all vibration, so I dont think I need additional dampening. @Mactadpole...

It's ready for test flight now, just waiting for the rain to stop. https://instagram.com/p/3bihwmL5DP/ <---- link for video It feels really smooth, no thing like my older gimbals. I will tie down the cables, and make it a bit cleaner after test flights. There are also pictures of the...

I had some issues getting the board to communicate with the GUI after a firmware update. The solution was to flash with a recovery firmware, then erase EEPROM from GUI, and then install the firmware again. I´m working with IMU calibrations now. The manual Jakub made, has a good step by step...

A smal update from me: I have been struggeling a bit with my AM board. This has nothing to do with the gimbal itself, but probably more with my limited experience with AM. Jakub has been really really helpful. He has answered all my questions fast, and came up with all the sollutions I...

Thank you Jakuban. It helped a lot!

It's past midnight here, and a rain storm is coming in a few hours, so probably not before a couple of days :( Also I have not desided if I will try the CP or the AM board on it first. I would really like to try the encoders, but right now I find the AM with encoders a bit more confusing than...

Yep, I did. To complete the gimbal assembly is a no brainer really, so no instructions are needed for the gimbal itself. The gimbal controller however is not mounted, but the mounting of the controller and IMU's looks easy enough. The only challenge is where to connect the different wires on...

Just got my hands on the infinityMr, and first impressions are really good. Build quality feels really good, and the thumb screws are a really nice touch. Also deling with Jakuban has been a good experience. I have ordered the gimbal with encoders and AM board. I find connecting the encoder...