Recent content by onthebrinc

No the tx is not very the walkera f210 just came out in last 3 months (im sure the video tx can be older). Im gonna look for a list of channels. Thank you

I have a fatshark 5.8 ghz in my quanum quad and I have now purchased a walkera f210. Walkera and im having trouble determing a compatible video receiver. I will post the spec below but it shows it as a fcc and ce? Camera (700TVL): Horizontal Resolution: 700TVL System Committee: PAL/NTSC...

I now have about 80 minutes flight time onthe unit and overall perforance is great. Still drifts mildly to the right 50% of the time. C.G. is good very close to perfect.

I have read through tons of threads and the general statements have been that except for a very few everyone else that runs a mlite has gps issues. I'm going to keep trying and apparently there may be a flash for the future to update the software but mlite has a terrible reputation for gps...

I get a single green blink which ( i believe) indicates good gps with sticks centered. It does not do a circle or t.b.e. it just slowly drifts in a different direction everytime. Not bad or fast but drifts

Quad= Quanum Venture Tx: Spectrum dx6i, Rx: spectrum ar6210, Naza Mlite flight controller Motors= multistar mt2213 935 kv ESC= afro esc 20amp x 4 8''x4.5 Current batt= 2200 mah 3s After several attempts and adjustments my naza mlite does not hold loacation very well even after redoing the...

ok so, I am now able to let the quad sit for a minute and get the ma satlelite readingon the led. Its blinks green only when in gps mode and acording to the manuak this is as good of a gps lock as i can get. Atti mode works great the quad is very dailed in after making a few gain changes to...

Thanks Ok I understand the radio is not ideal but I have set it up to get 3 modes with 2 switches I have gps, atti and failsafe working. I can make the 3rd flight mode into manual however I didn't think I would use it much and wanted to make the failsafe return to home work. Last night I flew...

Quad= Quanum Venture Tx: Spectrum dx6i, Rx: spectrum ar6210, Naza Mlite flight controller Motors= multistar mt2213 935 kv ESC= afro esc 20amp x 4 8''x4.5 Current batt= 2200 mah 3s I have about 25 minutes of fliht after going through all the setup. It was a bit of a learning curve to setup...

Unfortunatly I cant weigh the unit, yet. I will get a scale. I will grab some bigger props. Thank you for input.

Quad= Quanum Venture Tx: Spectrum dx6i, Rx: spectrum ar6210, Naza Mlite flight controller Motors= multistar mt2213 935 kv ESC= afro esc 20amp x 4 8''x4.5 Current batt= 2200 mah 3s After spending a decent amount of time setting up the naza (learning curve) i was able to make a maiden flight...

Reloaded ething and it now communitcates. Thanks to all for your random act of assistance. Now to set it up

I reloaded ething and now all works. Thanks

Hookup: naza mlite m1,m2,m3,m4 are connected to the corresponding speed controls a= aileron e= elevator t= throttle r= rudder u= aux 1 (but I have tried this on the gear slot also) x3= vu I then binded my dx6i to my ar 6210 ( solid amber light and I tried a test servo and it was responding )...

yes I have loaded drivers and reloaded driver, tried 2 different cable. Super frustrating I have been rc'in for 20 years built 50 plus models and never had a device I could not make connect. Hobbyking has no support, dji tell me to contact hobbyking?