Recent content by kemmy

Thanks Ferdinand. This was the kind of info and chart I was asking for. :) I'll let you know more about how I get on once I get my parts from the CNC router :) Thanks again. Kemmy

Well I also think it would be a great project to work on but only after someone helps me out with the 12S config and what way I should connect my Wookong M FC to a 12S power system.

Hi everyone. I just wanted to ask and get some advice about a multicopter system I’m building. Basically I decided to use the Tmotor U11’s I bought a few months ago. The system will include these components listed below. 8x Tmotor U11’s in a X8 config. 8x Tmotor T70A PRO (12S ) ESC’s 4x...

Hi again. Thx for the reply.Yesterday I met a guy who builds full RC systems , including multirotors. He told me that my hobbywing 40A platinum ESC(he told me its slow and would be good for aircraft or heli only but not for this specific multirotor motor) is no good for my motor (which is a...

Hi there. I'm having some trouble with my motor-esc combo. My motors are 18pole Sunnysky kv320 v4014-12 and my ESC's are hobbywing 40a platinum series which only support up to 12 poles. People suggest me to buy new cheap esc's and flash them with SimonK. Is it possible to flash my remaining...

They all work great. I checked my connection ends with voltmetres before they are ok. I contacted foxtechfpv where I bought my hobbywing 40a platinum esc's before, They told me to set the in-angle to low , so now I'm trying to figure out how to set a low in-angle on the esc, there is no menu...

Thx I left my timing at 15 (5 in some settings it shows) which was the default timing. When you said high pole count what do you mean ? (sorry I'm kinda new with multicopters and building RC systems) I can use my esc programmer card to increase the timing if all those dont work would you...

Ok!! I figured out this is a "COGGING" problem but so far I havent found any solution or answer to do with this problem. Some people suggest its a ESC problem and flash the ESC's etc but never heard anyone fix this problem successfully. I don't even know in the worst case scenario what I would...

Hi there. I was having some trouble with my sunnysky kv320 and Hobbywing 40A platinum ESC's. When they worked all together on my octo some motors wouldn't spin correctly. They do that even when I try them individually. Doesn't always happen but sometimes at low throttles the motors seem to get...

Great vid mate :) I'm also building a very similar setup. How did you manage the gimbal and anti vibe plate mounting ? Because of all the cables I had to use some longer screws to open space between. Great vid btw, hope mine will end up the same ;) This is what I was talking about when I said...

Ok now that I'm done with soldering everything (harnesses , wires, connectors etc lol ) for my octocopter that I'm building I wired my WKM parts together to do a pre-setup so I could see if all 8 motors are working ok. I have a problem with the Tx calibration though. I don't know if I'm doing it...

Hi everyone :) I have a problem to do with my ESC-motor-Rx-Tx connections. I'm using my ESC's for the first time so I'm setting my throttle stick to the lowest position on my transmitter. When I plug everything in , power , receiver etc I get this constant beep-beep-beep error with 0.25...

Merhaba tomh :) hehe. As far as I know you only need to get permission from the municipality. Unless your filming historical places that are under protection (the ministry of culture) only a permission from the municipality would be enough. There is no law or regulations/limitations for flying...

As far as I know the DJI wookong m can take a connection directly from my 6S 22.2V lipo. The WKM PMU can handle high currents.

Thanks again Maverick. I have one last question. I noticed it was charging a little slow, I charged it over 30mins and it only went from 3.8V to 4.2V so I changed the A1C to 3C but then it seemed like nothing changed :( Is there a way to speed things up in a safe way ? On my battery it says...