So I've been planning to build my first quadcopter (with a twist) for the past few days, and I've come to the part of the building process where I have to buy all of my components. I'll list out the products I plan on purchasing, with their weight and price and other specs. If you guys have any suggestions/tips to share, I'll gladly take them 
Motors: Turnigy Multistar 4220-650Kv $23.28/ea x4 65g/ea x4
Propellers: 1055 Carbon Fiber Propellers $7.74 for a pair of 2, x2 8.5g/ea x4
ESCs: Turnigy Multistar 30 Amp Multi-rotor Brushless ESC 2-4S (OPTO) $11.29/ea x4 32g/ea x4
Battery: Turnigy nano-tech 5000mah 4S 65~130C $76.59 576g
5v UBEC Step-down converter (for MCU & 'receiver'): http://www.adafruit.com/products/1385 $9.95 ~10g
Frame: Carbon Fiber Square Tube for arms x2 $4.80/ea 77.746g total, Woven Carbon Fiber Sheet for center plate(s) $22.66 (not sure about weight here, I plan on cutting a circle so ~30-60g?)
LV Alarm: On Board Lipoly Low Voltage Alarm (2s~4s) $2.15 7g
+~300g for headroom and controller.
Here's where the 'twist' comes in: I'm going to be using a combination of a Raspberry Pi for control and an Arduino Uno for gyroscopic/accel. stabilization and sending the PWM signals to the ESCs. My reason for doing this is because I'm a DIY-freak, I like to do things on my own. I know that this is by no means going to be a trivial task, that's why I wanted to do it
Here's a write-up I did explaining why I chose that control setup: http://muny.us/quadcopter/Control Options.odt
Total cost: $297.70
Total est. weight: 1400g
I looked up the thrust charts for the motors with the props and I should get ~700-800g of thrust per motor, so 3200g in total. More than enough, ey?
If you feel I left anything out, or have any suggestions, please feel free to reply
Cheers!
Motors: Turnigy Multistar 4220-650Kv $23.28/ea x4 65g/ea x4
Propellers: 1055 Carbon Fiber Propellers $7.74 for a pair of 2, x2 8.5g/ea x4
ESCs: Turnigy Multistar 30 Amp Multi-rotor Brushless ESC 2-4S (OPTO) $11.29/ea x4 32g/ea x4
Battery: Turnigy nano-tech 5000mah 4S 65~130C $76.59 576g
5v UBEC Step-down converter (for MCU & 'receiver'): http://www.adafruit.com/products/1385 $9.95 ~10g
Frame: Carbon Fiber Square Tube for arms x2 $4.80/ea 77.746g total, Woven Carbon Fiber Sheet for center plate(s) $22.66 (not sure about weight here, I plan on cutting a circle so ~30-60g?)
LV Alarm: On Board Lipoly Low Voltage Alarm (2s~4s) $2.15 7g
+~300g for headroom and controller.
Here's where the 'twist' comes in: I'm going to be using a combination of a Raspberry Pi for control and an Arduino Uno for gyroscopic/accel. stabilization and sending the PWM signals to the ESCs. My reason for doing this is because I'm a DIY-freak, I like to do things on my own. I know that this is by no means going to be a trivial task, that's why I wanted to do it
Here's a write-up I did explaining why I chose that control setup: http://muny.us/quadcopter/Control Options.odt
Total cost: $297.70
Total est. weight: 1400g
I looked up the thrust charts for the motors with the props and I should get ~700-800g of thrust per motor, so 3200g in total. More than enough, ey?
If you feel I left anything out, or have any suggestions, please feel free to reply
Cheers!