Selling this Octo for a friend. It is all built and ready for you to tune to your liking and fly.
This entire setup is brand new, it has only had a single test flight. At that point he realized it was more than he was prepared for so it is going up for sale.
Here is the equipment:
-Droidworx AD8 HLE
-MK2.1 / NAVI 2.0 / GPS 2.1 with GPS shield 1.1 (Pics show original boards, were updated with newest version boards)
-New SmartOSD (not installed)
-New MK Plug-N-Play XBees
-AXI 2814-22 motors
-MK 2.0 BL ESCs in Octo distribution board (i2c isolator so you still fly if one esc fails)
-AV200 Photohigher Camera mount
-2x Multiplex LN-6015 chargers
-5.8GHZ 600 mw transmitter/receiver for copter camera (not installed)
-1.2GHZ 1watt transmitter/receiver for camera feed
-Graupner MX-20 with all the accessories ($900 alone)
-Graupner lipo upgrade
-Graupner protection bag
-Graupner neck strap
-Contest S-Pult Carbon fiber MX-20 transmitter tray
Copter is setup with giant 8mm bullets - FYI if you need to order a new connector for your style of batteries.
The photos below show the original build with the older Navi and GPS boards, they were upgraded to 2.0 equipment and have been setup and bench run but not flown!
This copter is fully built and in a specially designed crate. It will come to you FULLY BUILT and ready to plug in. 0 build time here!! The crate is large and will have to go UPS Freight or some equivalent. Pickup is in LAS VEGAS if you don't want to have it shipped at your cost.
He would like to get $8000 for this setup, there was an initial investment MUCH more, well over 13K.
Thanks!
This entire setup is brand new, it has only had a single test flight. At that point he realized it was more than he was prepared for so it is going up for sale.
Here is the equipment:
-Droidworx AD8 HLE
-MK2.1 / NAVI 2.0 / GPS 2.1 with GPS shield 1.1 (Pics show original boards, were updated with newest version boards)
-New SmartOSD (not installed)
-New MK Plug-N-Play XBees
-AXI 2814-22 motors
-MK 2.0 BL ESCs in Octo distribution board (i2c isolator so you still fly if one esc fails)
-AV200 Photohigher Camera mount
-2x Multiplex LN-6015 chargers
-5.8GHZ 600 mw transmitter/receiver for copter camera (not installed)
-1.2GHZ 1watt transmitter/receiver for camera feed
-Graupner MX-20 with all the accessories ($900 alone)
-Graupner lipo upgrade
-Graupner protection bag
-Graupner neck strap
-Contest S-Pult Carbon fiber MX-20 transmitter tray
Copter is setup with giant 8mm bullets - FYI if you need to order a new connector for your style of batteries.
The photos below show the original build with the older Navi and GPS boards, they were upgraded to 2.0 equipment and have been setup and bench run but not flown!
This copter is fully built and in a specially designed crate. It will come to you FULLY BUILT and ready to plug in. 0 build time here!! The crate is large and will have to go UPS Freight or some equivalent. Pickup is in LAS VEGAS if you don't want to have it shipped at your cost.
He would like to get $8000 for this setup, there was an initial investment MUCH more, well over 13K.
Thanks!
Attachments
-
1.2GHz 1000mW RX TX AV setup 1.jpg -
5.8GHz RX TX AV setup 1.jpg -
2012-06-14 17.20.32-54.jpg -
20120127_170808.jpg -
Boards' empty boxes + MK-GPS shields (not installed yet).jpg -
Brand new clear, ventilated dome.jpg -
Everything related to batteries & chargers (include 3 pairs of NIB 8mm bullets).jpg -
Graupner TX + all additional goodies.jpg -
IMG_1299.jpg -
IMG_1300.jpg -
SmartOSD.jpg -
The accessories box.jpg -
XBee & MK-USB.jpg
