Search results

Yuneec!

OK starting the rebuild but was curious if there is any product I can use to wrap say my UHF RX in to make it look nicer say like black shrink wrap or something? Anyone done something like this?

The go pro was found a good 30 ft from the body lol. And amazingly I found the sd card as it popped out somewhere during the fall. So I have video of the fall from both gopro and fpv. But doesnt tell me much

Haha ya I think a prop broke mid air. It seems like the flighr controller was still responding but was able to stabilize as it just barrel rolled to the ground. It hit a sloped roof. All the peices then scattered across the back yard

You know does anyone recommend a brand or set of Torx screwdrivers or at least a T8? I keep buying the sets at my home depot and lowes and they literally strip after a few screws! I sont wanna spend $300 or something crazy on a set of screwdrivers but there has got to be something better out...

ya im really worried about my NAZA V2. but it does power up and the usb link works fine when in the NAZA software, so im hopefull. My RX is shot tho as the MR landed on the back directly on the RX.

OK thanks. Also I recently had a pretty bad crash from 300ft are the ESC's pretty resilient? They don't seem damaged, one is a bit scuffed, but should I retire them and just get new one just to be safe when I get back up and flying? What about the motors too? They look ok but.... who knows.. Id...

So what voltage do you guys usually drain your batteries down to in flight. Ive been stopping at 15.1-15.3 volts can I go further? Ive noticed im not getting even half of the mAh rating that the battery contains according to my current sensor. So like on a 4500mah battery it says ive only used...

Im having a similar problem. In manual mode my hexcopter flys just fine. But in atti mode it barely gets enuff power to take off, and seems to wobble on the ground as if its trying to correct its balance as if it was in the air. I can see individual props speed up as if its trying to level. Is...

OK sounds good is there a better way to turn it off for good though in the settings so I don't have to worry about disabling it each time?

I guess that's my biggest fear that im actually transmitting 2.4ghz and 433mhz so I wanna make sure

So is that the only way to make it not broadcast the 2.4ghz signal while your running the ezuhf?

Thanks Chris! I have updated the firmware on the TX and the diversity 8ch RX to 1.44 already, I have the manual, and the installer but I didn't notice you could bind with the software so ill have to go back and try that :D.

OK guys Im really hoping to have this guy ready to fly so I can maiden it and take it camping this Friday, would be able to get some good video. But im still having a problem linking my futaba 8FGS with the EZUHF and possibly binding. When I bind I get the 3 flashes but followed by pulses of...

Ya so for the hexcopter I just used the stock DJI f550 gear in the end. The 690kV turnigy motors I ordered were just way! to powerful for the turnigy talon frame, and the frame was kinda flimsy to begin with. I also bought a TBS Discovery and am about to maiden it along with a TBS caipirinha...

O and I still have to order a 2.4ghz patch antenna. I see HK has one for $15 and TBS has one for $70 is there really a big quality difference between antennas....? or is TBS just overcharging.

OK almost done with the builds :D But I have a Futaba 8FGS and am using a fatshark dominator and the lawmate 2.4ghz tx/rx and the EZUHF 433Mhz tx/rx. So my question is im building my "ground station" I want to power the goggles from the controller but they are 12v and the battery in my futaba...

OK and what would any of those beside the gimbal be good for? and what is canbus lol?

I'm sorry I didn't mean the unit was bigger just that the whole setup takes up more space since its led and pmu are separate