Search results

Quick question, will the self tightening props work on the P1 V1? This was the first one on the marked.

Will these work with the NAZA http://www.ebay.com/itm/Hobbywing-Pentium-30A-Brushless-Motor-Electronic-Speed-Controller-ESC-5V2A-BEC-/320942133430?pt=LH_DefaultDomain_0&hash=item4ab9a450b6 These are V3.1 I see, or do I need the FunFly ones?

Something has happend to one of my hobby wing ESC, out of 4 one acts like its crazy. Tested it without the Naza and only a RX and it acts like nothing I have seen before. But to make things easier with wires and stuff, I thought about buying 4 of these...

In a previos thread I got a reply to buy Graupner el. props 10x5 as they have 8mm center hole and those would fit the original X650 motors, but they dont! I also bought some with 6mm and a 8mm prop reamer, but then that didn't work either :( Are there eny alternative props fitting directly on...

As I'm slowly gaining hight I get less and less sight/control of my X650. I would like to add som LED light making it easier to orientate :) On my X525 I have put LED strips under all 4 arms, but for the X650 I would like to make something looking more thought through, and stealth ;) I see that...

I can't understand why it started to do this out of the blue! It has never been crashed, never gotten any hits, it has never even been landed hard. It only has about 10 flights in it, and all of the sudden it startet to shake at low throttle, WHY...

I have tried everything, but from time to time my x650 get this shiver for a fraction of a second, then it's smooth again. The X650 is stock but with two 3S 2200 lipo. They are stacked on each other to fit on the battery plate, maybe it's get unstabil as this gives a low CG? But I read that if...

I'm sorry for all the questions, but as a beginner on this FC I haven't any other choise then to ask questions ;) If I give it rudder input to the right it goes to a quick stop as soon as I centre the rudder stick. When I give it rudder input to the left and centre the stick, it keeps on...

I have set up the switch failsafe, without any problems. It switches between A - FS - M. But I would like to set up my Hitec Aurora to make the Naza go to failsafe if the A9 loses signal, has a brown out or gets turned off! I know how I do it, but I see that there ain't a way to make one channel...

What would be a good starting point for gain settings on a DJI Naza for a X650? I'm looking for some start settings, and then I can fine tune it in air with the knobs on my radio.

My small 3s 2200 pack are a bitt light and low on power. Tought I buy a 4S lipo, but I wonder what is the max mAh it will carry together with a gimbal and a gopro? Would a nanotech 5000mAh 4S be to heavy?

I'm out from my first flight with the Naza FC in my X650. Everything was great! It's super stabil :) But I don't understand that LED blinking! Everyting boots up perfect, I set it in Atti mode, orange led flashes, all is fine, but when I give it throttle to climb, the led turns to flash red. I...

I'm setting up my X650 with the Naza FC. I have been told that the Naza won't run the original X650 ESC's so I ordered and received some new HobbyWing FunFly. The cables on the HobbyWing ESC's are to short, and has no connectors. My question is do I extend the RX cables and the power cables, or...

I had my X525 quad running very stabil, with a KK 5.5 board and KK 4.7 firmware. In a moment of looking the wrong way, two of the props hit a branch and the the quad tumbled down inside the tree. I would call it a soft landing, nothing really broke, except two two props that I now have...

Anyone know where I can buy some X650 ESC Covers, that has them in stock? Snapped one assembling my new X650 V4 :upset: :tennis::tennis:

I'm setting up a X650 V4 with the DJI Naza. Should I remove all the red wires comming from the ESC's, do I leave 1 connected as I did with my KK5.5 multiboard? I have bought ESC's that can handle up to 4S, the Naza can take up to 6Ss, do the Naza have a build in BEC, so that my RX don't get...