Search results

Hey sir, I sent you an email, but am interested in two of your batteries! Possibly all 4 if they are still available come the start of the month. Cheers! Let me know what the shipping is and where to paypal it!

Hey man, I'm from Soflo, currently up in Plantation though, originally from Homestead. Hows it going? I cant tell you what the market is. Its there to be made, but depends what you do. I am just trying to break into some things myself. Good luck sir.

Right now I am flying mostly Naza lite, v2, and a kk2 with the 2.1 firmware. I also bought an APM2.6, but it was dysfunctional (unlucky ebay buy, i tried reflashing the bootloader, but still cannot upload any firmware onto it) but I messaged the seller and they are actually sending me a...

Oh look, a reply! Well to do my good turn, the RCT800 arms are very stiff. Very little flex, although if you're running huge motors, and dont balance your props well, it will carry the vibes. They weigh.. (one second)... approximately 110 grams. Pretty heavy. I ran a hex with them using...

Thanks guys, I'll check check to make sure the motor mount are level though I suspect right now its the motors themselves. Once the shafts come in stock I will replace them. Thanks but no thanks to the guy selling the T motors, I love my sunnyskys just fine. These 3508's just had a bit of...

I am using new escs, though this problem has persisted through the previous batch as well. Right now I am putting most of my doubt in my motors. I believe at least one is likely to have mildly bent shaft, and bearings need replaced. They are the 3508 580 kv sunnyskys and unfortunately they are...

Hey guys, I have been using a Naza v2 for a few months now, and in all of my builds using it, it has the same problem. Rudder right: it drifts a little extra after i go back to center stick. Rudder Left: its slower to yaw, and upon center stick, yaws right about 10-15 degrees before...

Hey guys, So I started with drones with the start of this year! I think it was the end of last December when I started to built my first f550 (having owned an ardrone2.0 a year prior). It started with one drone, and quickly branched into my full fledged obsession. It grew from a big...

You could change your exponential values, I don't know why it turns though, i have the same problem. :| I'll letcha know if I find anything out. But yeah for now to be safe, you can try keeping your gains super low (mines at 60 for a big quad) but even then, jamming hard left to right...

I don't know the solution except to guess that your center of gravity might be off. I am having trouble with this on a a big quad using a reptile frame, if I yaw hard left to hard right the thing nearly drops itself. Lower yaw gains will help, but of course you lose at turn speed.

Hi guys, Disaster has stuck. While rebuilding my f550 on clean plates with new motors I messed up bad. Despite it being the 5th time, i soldered my managed to solder ALL of my esc's backwards. I plugged in my battery only to see a the sparks, hear a pop, and yank it out. I looked at the board...

You'll be hearing from my agent :dread:

Haha I actually went to fastenal today for the first time, and they didnt have any in stock. They could have ordered them but I stopped by my local hobby store and found they had the clips. Neither had washers in the right size though :/ Thanks for the advice, it would have saved me if I...

Thanks guys, I found some replacement e-clips at the local hobby store. I checked a fastener store but the parts were too small and out of stock there. The washer is proving to now be the more difficult part to find but I will make a temporary fix in the meanwhile. I will have to get proper...

Hi guys, I just got my FPV in (teleporter v3) shortly after replacing my bearings with ceramic ones. It was all going well.. until I noticed my back two motors acting strange. I discovered that the E-clips and washers on two of my motors have come undone and they are gone as gone gets. My...