Search results

Ronan Thank you for the well wishes. I agree with the philosophy of redundancy, however, this $3000.00 component worked for about a dozen flights and stopped working without provocation. I've spoken to DJI and the dealer. Each blames the other for the lack of support and we're stuck in the...

No luck. I mapped the AUX1 channel and tried it in on/off positions without luck. Both 5Ds don't work with it. Two Vtxs don't work. It's a $3000.00 paperweight that'll take 6-8 weeks to fix. Not happy.

I'll certainly look later on and report back! Thanks bro!!!

Thanks guys. scotth- The Zenmuse doesn't support HDMI. I'm not sure what you mean by your comment. Can you explain further? Thank you!

We've been flying an S1000 with the Z15 5D successfully for a few months w/o any issues of any kind. Seemingly for no reason, the Z15 stopped communicating with the Cannon 5D. The camera settings are exactly to spec for DJI use and the machine is otherwise unchanged. However, the 5D scene...

Carapau saved the day. I simply missed a fundamental channel error. This is an event that largely goes under reported. -I made a mistake- A2 didn't let me take off- Well done dji!

I've set a few up on S1000s and cannot figure this one out! I've done: Updated all the components Sticks cal ok (14SG) IMU cal inside Compass cal outside All motors passed F/S IOC and fight modes all functioning normally Home position indicates saved Rotors won't spin.... Any ideas...

Thank you very much for the information. The only issue is that it does not show that the system goes into failsafe when I turn off the transmitter. It remains in whatever flight profile I have left in.

There's a fantastic video that I didn't bookmark. The guy explains the procedure of how to setup a 14SG w/ A2 to kick on RTH. Does anyone know how?! Thanks!

Thanks for the thoughts, Craig! I swaped both the RX and tx without any changes. I have a new sat ant to try. Ill let you know how that goes!

I wish. I've swapped out all the components. I'm really disappointed that it didn't work out. I have no magic bullet as of yet. Have you tried swapping out your controller?

Check this out, this is what the channels look like when I'm plugged in! This can't be good and is likely contributory. But I don't know what the source is. And yes I have recalibrated a bunch and it does this every time. http://youtu.be/U4Wir_P7tao

Thanks Bob! I'll trial those settings.

Not sure what you mean by "blips". ?? Do you mean some kind of interferance or flashing of the pointer on the throttle scale?

First off, thank you to all who have been very helpful with my previous posts! I've got a professinally built f550 with the following: NAZA-M V2 Heavy lift- T-Motor MN3510-13 KV700 x6, TMOTOR Carbon 12-4 x6 Zenmuse H3-2D Gaui Vision 100 5.8ghz Pulse 6600mAh Naza M V2 Settings...

Still getting my butt kicked in GPS mode! It flies great in Atti mode, so I'm missing something... Finally got a 6600mAh Pulse and mount it with the AC balanced. Just for info sake: To what physical point on the sat antenna do you measure? (Top, middle or bottom) And is the other measured...

Extremely helpful, Steve, thank you! Now that I know what the tech will do, my input is cemented. I've read all about "toilet bowling" and I believe I'm caught in the flush. I live near Boston MA and found -14* is the declination setting, thus, 14* to the left is required. I adjusted as...

I'm replying to my own issues as I solve them for efficiency sake! I found great success in punching up to 60% and letting the machine come up. BRILLIANT! I've tried to spend as little time as possible in ground effect in landing and have gotten better at "planting' the machine, rather than...

Thank you! I did just fly a bit and everything seemed to go ok until landing. I lifted with a "medium-paced pop" and it rose-up straight for the most part. You're suggesting I quickly slide the collective to ~50% and let it rise quickly to a hover? On landing it didn't settle straight down...

Thank you all very kindly! Your information brought me right to lift off! Now, I've spooled up in atti and the 550 wants to roll over just before skids up. Things I've double checked: Props all proper direction Programming perfect Calibration both programmed and done outside with...