Search results

I have definitely never had this issue.

What is the symptom of this? I have an orange 8 ch. on one of my HFP X8 and I don't notice anything. Been flying it for a couple years. I use them on the gimbals as well. I run futaba Rx on all of my other models, but they seem to work fine for me.

Or those telling you to sell , or not buy, what is currently on the market is obviously not working at the moment. The AV200 can put out very usable footage with the skyline. I still get better footage with my AV200 and skyline than with the other systems I have tried. I would not be working...

I finally got a working OSD Pro plugged in. The other unit must have been faulty out of the box. I can't believe between the E-logger V4, OSD Pro and GPS that there is no Artificial Horizon. Do I really have to add the Guardian Stabilizer for that? This is getting out of control the amount of...

I guess it is the Eagle Tree gear that is putting this over the top with it's own voltage reducer and filter. It sure would be nice if all of the flight control board had built in OSD. I might have to throw a HFP on here to see how it works with the GPS. Seems it would be a cleaner install than...

Iris, Will you post some photos of how you have your electronics laid out? I'd like to mount mine with either a CC3d or Naza/gps. I also plan to install eagle tree, a camera, vtx, and a gopro. I am finding it hard to fit everything and still be able to have it fold. I may add another layer of...

Yes, Beepy is an understatement. LOL

Sold

I hope it is not the Module, I have already replaced it once and I have only flown this one a few times for testing. I have the D2523T module. I do have a spare ublox wire, but just want to confirm that I need to modify it so the pins are not lined up.

PM me. I may sell just my GH2 Body.

Maybe it is because I am not used to it, but the beeping while under 7% is a bit over the top. I would like to request to have the safety beeping removed.

I just installed, calibrated and flew the first pack. A bit windy, but it felt very similar to old firmware. I am having an issue with the GPS getting stuck on blinking purple. I could not arm the HFP and had to unplug about 15 times before GPS board would arm. I am wondering if I have a bad...

I submitted a ticket. I have a second elogger and it did the same thing with that unit. I think I have a DOA unit.

Yeah, everything seems correct. Triple checked. OSD PRO is not recognized for some reason. No RSSI input. I only have GPS so far.

I am blown away how many issues I am having with what seems to be such an easy system. So, now I have the 4s battery harness soldered to the ET elogger. I have another wire running from the battery harness (soldered to where the wires are hooked up to the elogger as well) through the step down...

I had the same problem. I had to reverse the Elevator channel in my radio (futaba). Try reversing it on the assistant first. see what happens. It is dumb they have a horizontal slider image on the software for Elevator and throttle. Graphically, it should be vertical. Also, make sure your...

Thanks for that. I have these items around so will add them. My little FPV quad is getting crammed with gear and I don't even have a gopro on it yet. I might have to bump up to some 2814s I have sitting around.

I was just about to post these instructions. RCman put this together and it is absolutely crucial for safely using the 8fg with a HFP.

Confused..... I am going to be hooking this up to a 4s battery. How do I power my 12v camera when hooked up to the OSD Pro? Do I need to run the power to the camera through a BEC? The Vx transmitter can handle 4s, but I don't think the camera can.

No one can recommend an overall weight. You need to decide what you are going to carry and then build from there. I have not seen too many people build a quad with 2826 motors although I am not saying it can't or should not be done. What is your goal with this quad? Are you going to lift a...