Search results

I finally completed my build, Xaircraft X650 V4, turnigy 2826's, turnigy 30a plush esc's, WK-M & Spekturm DX8. Problem is that when I fire her up, 2-3 of the motors spinup, once I hit 50% all the motors fire up. I lifted the unit off the table while the motors are spinning and tip her to the...

My 2 Cents "When the people fear their government, there is tyranny; when the government fears the people, there is liberty. " Thomas Jefferson

Red wires were removed, and props removed, been there done that, three minor cuts on the arm

Yep, and still nothing on the one esc, so I have to assume that its bad

I just pluged in each esc and three of the four were able to be re-programmed. The fourth on emitted no sounds and never programmed. Ordering a new one tonight Thanks for the help Shawn

You are so right. I've been ordering from a place in TX with great results. Goto: http://www.ebay.com/itm/METRIC-SOCKET-HEAD-CAP-SCREW-STAINLESS-M2-5X6-MM-PKG-OF-25-RC-CARS-TRUCKS-/360454189025?pt=Radio_Control_Parts_Accessories&hash=item53ecbe6fe1 These are great screws and the price is...

Ok, I've researched the internet, research this site, tried everything and then some but my problem is still nagging me. So after spending a full week trying to fix the problem on my own, I have finally given up and am going to ask for some help I'm converting a Xaircraft X650 FC to a Wookong...

Glad to see that someone else has taken the time to fine tune the Xaircraft X650. My experience is pretty much the same, I have re-worked my units so many times I can do it in my sleep. You must make sure that your unit is level, if your working on the X650 4 or 8 YOU MUST level the booms...

In the United States the best place is: http://www.heatsinkusa.com/ - they will custom cut to the exact size you need

The screws are cheap, I either have to use a hex or allen key to remove them sometimes. Then I find they are slightly to rounded within the hole. So I got tried of it and used my dremel to cut a slot across the center and converted them so I could use my flat head screwdriver. I found this...

You can, from everything I've read they work better as a camera stabilizer. However you will need to get a BEC to power it.

I have to agree with you 100%, I also have two Xaircraft models, I'm chalking it up to a learning experience. I am considering the Xaircraft units as a costly, but informative learning lesson. I can't get pissed, apparently numerous people have made the same mistake. You live and learn. I'm...

My exact settings: Flaps (Norm +100 Land +56) - (RTH) Mix 1: Gear-> Gear ACT - Rate D - 65% U -100% - SW ON Trim ACT (GPS * ATT GPS) Sub Trim: Gear +100 Flap +100 I pushed all my switches in the up position before I started, If you don't you can always reverse the switches to your liking...

Just dealt with the same thing, here's my setup: GPS & ATT Mode are channel 5 make your flap toggle your RTH - Go to your menu and make sure you make your Flaps 100% - That should fix your problem

Fixed a few hours later, forgot to post

For a long time I sat back and watched on and off Gentlemen flying RC airplanes here and there. I was always amazed at skill and patience it took. I was always amazed that people actually took the time to master a hobby that cost a small fortune. Over the years, I too also picked up hobbies...

I have a Spektrum DX6i with a ar6210 on a Xaircraft 650. For some reason I can't get the GPS / Auto to connect or even be seen by the DX6i. Can someone please send me the proper settings for the DX6i? Its most likely something I did and just don't see it. Having some serious senior moments...

Being new to Multi Rotors, I would like to know if the Naza Gps will work with the Xaircraft FC. The clerk at my local hobbyshop told me it shouldn't be a problem. I have been lurking for a bit here and have yet to see anyone post anything about these two items working together. Could someone...

Batfire - thanks for the help, after some research and playing around a little, I find that your answer was totally correct. I was not aligned and there was no pad under the AHRS. I've had her back in the air for about a week now, but I did add the padding tonight as soon as I got your reply...

I'm in Atlanta, GA and would be glad to help you anyway I can