Search results

OK. I am going to try to get rid of my steel hardware. I can probably get away with some Aluminum 4-40 1-1/2" socket cap screws, but just barley on the main plate side. I would like to try to install some insert nuts rather than using regular nuts, so I can save time with dis-assembly. Has...

I have not had success with my GPS. I even sent it in to HF to be inspected. They said it worked fine, but it won;t work on my X8, Y6 or my new Octo. George told me to replace all fasteners with aluminum to fix the problem. I just have not been able to find a good source for aluminum hex head...

Also, can someone point me to instructions for using a JetiBox? EDIT: OK, that was fairly straight forward. Plug JetiBox into the Picklock on bottom row with signal wire in the bottom left corner of plugs. It should communicate and then offer basic steps to follow. Documentation for Picloc is...

I've read on this forum about quite a few folks having Jitter issues on the tilt axis. I have always fought the jitter and it seems to be as bad as ever right now. I just spent a couple hours drilling new holes in the AV200 camera plate to balance Canon 5D/16-35mm lens and I still have really...

Why 60C? My 25C GensAce seem to hold fine. I may get some 30C 5300 5s packs. Tey are almost half the price of the 60C. ...Although I think I just lost a cell in one today. I still have to charge it, but I may have over discharged. Testing flights on the new Octo build.

I just ordered a new gear kit. I'll post if it fixes it. This may have happened during gimbal set-up (full roll on plug-in scenerio) or a past crash. Not sure, but I am not blaming the manufacturing. So I wouldn't fret about ordering one. They seem like quality servos. I just couldn't see any...

I have been having some issues with a grinding noise on the roll axis, so I opened up the Savox servo. I found that I could get rid of the noise (clicking when not installed on the gimbal) by lifting the lowest gear. Anyone have an issue like this? Anything I can do about it? What is the...

Hub balancing I am curious about the same thing but with my APC props. My 14x4.7 props all have huge amounts of Velcro/CA glue to balance the hug and the mass sticks out pretty far. I then feel like I get just as much, if not more vibration issues. I have had a really hard time balancing...

I have also struggled with this over the years. It would be nice to reverse the rotations.

As I take a break from soldering my new wiring harness, I am wishing I had a set of these escs and the wiring harness. I like it. I use the plush escs anyway, these might have to make it into my next purchase. The 45s will be great for the y6.

Hey guys. I am picking up a used RSGS to try on my AV200 (V1 but may spend some more $ on making it a V2). I have not read this entire thread, but do seem to remember reading about various wiring harness modifications for different batches or the RSGS. Do I need to be concerned if I get one of...

I think I am sold too. I just sold my T2i on ebay last night. Hope they ship soon. I am sort of hoping there will be a price drop on the GH2 as well to have a backup or for test flights.

My y6 with HFP Has very smooth Yaw. Same as my X8 with HFP. I do have some issue with altitude change when yawing, but that seems to depend on how it is tuned and varies each firmware releases. (although it may have more to do with vibration issues than software). I am again rebuilding both:)

What thickness CF plate are you using? What is different about this from any other center plates on the market? Will it be easy to remove arms or fold for transport? Not trying to be critical, but I am looking for a solid center plate design for my next build. Y6 Octa.

I still have not tried any Xoar props but thought it was about time. I am looking through the Hi-Model.com website and see the JFX props. They are quite a bit cheaper than the Xoar sites (although not as cheap as they appear after shipping and 3.5% fees). Anyway, I am unsure of the model to...

Every one of the Nano-Tech lipos I have ever owned puffed way too fast. Even with watching to not over-discharge. Go with Gens Ace! I have been using them for over a year without an issue.

No, my bearings were not marked EZO. They are unmarked and came in a T-Motor package via ClubHeli. I am also fighting with dirt getting into the motors and melting to the green coated stators. I think this is what it is. Sometimes I need to take off or land in an area where dirt flies as I...

I've had the 2826 500kv T-motors for about 6 months. I have gone through bearings on pretty much every motor. I also just replaced two sets of motor bearings tonight with new T-motor bearings. One set came faulty in the package. I have been fighting vibes since day one. So, I am on the search...

I've read quite a few posts about others having issues with over compensation (mine is constant twitching) during flight that does not show up when going through set-up. Sort of like the servos are hunting from vibration issues. I also seem to get everything set-up fine at the desk, then go...

George, Are you replying to PM and email? I have sent you about 5 messages in various forms over the last 6 weeks with no response. I am still having the old USB connection issues, I have tried soldering a few times. Please get back to me. Thanks.