Search results

Got the S800 today ! I must say the frame really makes sense. Gonna start a build and details threads about the components. Up to now the frame makes a really good impression ! Boris

As far as i understood it its two different things. There is a hdmi to analogue coming for/with the z15n Zenmuse, no statement yet on the z15g version if a converted comes along with it. The Ruling once released will not have anything to do with the converter anymore but will have a HDMI...

You can check out the remote gain in the config tool while you operate the switch. You will see what value you are switching to etc. But eventually putting the basic gains on a switch makes no sense since you can only switch between two values. Better is to use a slider or poti were you can...

ah s..t not cool probably something happened to my S800 on the way ;( TNT tracking message: 01 May 2012 06:01:50 Liege Euro Hub Held Hub-spec. Forwarding Need

Hi Cuong, its a little confusing what you are writing here: ----------------------------------------------------------- ESC: Hobbywing 40A for 2-3s lipo Battery: Gen Ace 5300 lipo 6s & Turnigy 6000 4s I recently found that the ESC only support for battery up to ? 3s therefore it would only...

Two ways to go sure to test Failsafe. Put it on you radio instead of manual flight mode for example. So you can test it without switching off your radio. Or setup you bird ready to start but props off. Start the motors but keep it on low rpm. Switch off the radio and look if the motors spin...

Cool thanks guys. I think I will only buy the kw4 motors from kopterworx now since they have the ceramic ball bearings. to bad there aren't any smaller versions for fpv copters. Boris

how do you guys take the bearing out. If than i am going to change them on all. I just don't want to do any damage to the motors by using to much force.

jape just took it apart and it seems like its the bottom bearing, I could hardly get the bell off. First i thought the shaft is bent, but eventually it can't be because taking it through the top bearing wasn't a problem. So the bottom bearing one must be deformed. Or not perfectly aligned with...

strange just flew inside a whole lipo pack no problems. So the difference is temperature and the strong wind it had to fight against, to the flight inside hmmm.

well thats a the thing it acts like all the others no rattling when i spin it and not play in any direction.

Okay i am going to change the motors. Just painful see a axi go like that without any impact or anything strange. Boris

Hi, was flying today with my FPV quad quite strong wind and eventually the back left motor prop esc combo started making strange noises and loosing rpm. My guess is its the esc would be the second simony flashed ecs going bad in a month ;(. Don't want to risk flying like this but also don't...

japp i think some of the staff. My sales person is gone till the end of the week. Boris

Disconnect any connections between the MC and the RX except AERTU and than the gimbal should not move anymore. You probably have some mixer setup on your radio effecting two channels at the same time. So one of your channels 1 ..... 4 it linked to 6 7 8. What do you have your radio setup to ...

minimal shakes on the descend down, but hey if i can get these results in that kind of wind, than i am putting the other copter in retirement !

You have a calibration screen for your TX in the config tool. Do all four slider move in the config screen do you have anything connected to X2 or X3 on your MC ? Boris

Munch are you sure that you are selling them for 12 each :) Wenn du sie um 12 Euro verkaufst nehme ich sie gleich :) bin auch in Wien. Boris

hmmm no clue. Announced are upgrades for WKM and NAZA. Don't know what will be in the WKM upgrade the only thing i caught on to, is that the flight characteristic between attitude and GPS mode should be the same with the next upgrade. Cant comment on it since i hardly fly in GPS mode, only for...

interesting approach to have a 24Khz Khz output I guess its addressed towards the ESCs ? 40A OPTO 6S LiPo...