Search results

Hmm wouldn't know. But who knows how their activation procedure looks. There is also some resetting of the MC possible combining one port with the other and booting it. Don't remember specifically though!

Japp it's version 2 got it a month ago. Single way point enabled or something more don't remember . Just keep it until you have your replacement and than send it back. I will tell you what the different shipment costs are etc by latest monday morning. I am in italy at the moment otherwise I...

Red I can send you a fresh replacement MC which I am not using at the moment. Can send it away earliest on Monday ! Boris

I think to remember but not sure anymore if you got a ESC32 with the AQ. If you did you could find out what the difference its between the NAZA and MC V2 for example. Naza for example sends out a minimum PWM value of 900. ESC32 didn't work before they were set to that. Boris

Red probably MC V2 sends out a different start PWM pulse. Ask Andreas if they tested the Herks with a V2 MC of the WKM. If not and they have he same issue than they will have to change sometime in their PWM firmware. Boris

Japp took you advice and didn't want to risk anything. Just did some Gopro action with the small TBS. Felt a lot safer than with a big one around the people and the explosions etc. Boris

Ah wait sorry i keep on forgetting if you have the DJI escs you have a hardcoded throttle range they can't be calibrated ! Experiment with you basic gains. If you can put them on a knob and push them up in flight until the copter starts to oscillate. Than bring them down again a little to get...

hmmm could have different reasons hard to say. Did you calibrate your ESCs ? You can do it like the guy in the video with a servos test or with you radio and rx. Hooking up the ESC to you throttle channel and doing the same procedure. http://www.youtube.com/watch?v=iklJEx3HA78 Otherwise it...

I eventually preferred to use solid walls or the fireplace and used the following, also knowing there are not wires close by in the walls etc. Switch actually every electronically device on the house :) Foam in a case. and than i used silicon cubes and sheets to filter out some more. I...

Okay Ill just put down some points what it could be. 1. Faulty ESC, spin up the motors without props see if you see any abnormalities. Don't go full on the motors to long not good for them ! 2. Motors issue, perform the same check like above ! 3. WKM NAZA etc. don't ask me why just boots up...

Hi Malc, can you give use a little more info on your setup ! Naza WKM ESCS etc Copter quad hex a etc. Pic would be great too ! Boris

morphsuite is in vienna. I just got news though that there could be something wrong with the board so i have to send it in for inspection. hmmm Doesn't really matter gonna take some more time anyways until i get the ALU arms for the TBS Boris

hahaha its not like i have a f... clue what i am doing here :) What the AQ FC wants though it that it gets frozen to -15 C and put in a airtight box and plastic bag, hooked up to a lipo and starts logging while the temps rises from the own heat it produces, to 40 C Than these logs are used to...

Okay i am going to stick to these logs for the static just can't get the mags better. Also compared to other MAG logs from other people and figured that my Y axis has a smaller range thus my MAG curves look more unstable but i guess its not the case. I hope they are fine this way ? Thanks...

If they are Opto it means that they don't have a built in BEC. If they don't have a BEC there is no need to cut the red wire. Why is your Quad dead ?

Okay guys. I am struggling a little :( Have 9 logs attempts behind me and i just can't get it perfect. Last attempt now outside in this box away from anything ! Temps are really strange. Outside temps are 10 C, board and static bag are warm after logging. Are these Y Axis numbers...

To tell the truth i am sick and tired of the typical viennese houses. It being my job and having to deal with them everyday :) Meme i will let you know. Should have more infos and finished CAD files by monday i hope ! Boris

HI DWB, must be a misunderstanding :) If you reached my website you will only see real-estate projects but no gimbals :) I just a hobbyist and not selling any MR gear. But post a link of the gimbal you were thinking about so we can comment on it. Boris

Damm i had that in mind when i ordered it remembering that you mentioned it before. But i didn't find the link ;( sugar.