Search results

Hi Snurre, I can't tell you since there was no AV out cable included and the one from the GH2 doesn't fit. I will check again to go sure. I am sure thought that 1080I out works although you are recoding in 1080p which didn't work with the GH2, so i am positive they didn't allow normal AV during...

Hi Rainer, nice to have you here. Start and thread an report what the problem are with you DJI setup. Regards Boris

Esprit Model announced in Rcgroups that they have their hand on receiver software for ppm out on R) Rx for example. One of you any contacts to jeti or some reseller so we can get our hands on it ? Boris

if the 730 isn't any bigger then the 740 than it is possible to get the 740 onto the zenmuse. I have seen it done before, just cant direct you to any more info. But if you have the zenmuse already give it a try before you buy anything else. I am with red though on this if you have experienced...

Thor are you boin to go Binger with the prop Size 16 ? And Andreas was Talking about that he is testung the dualsky 340 kvs. Did you have your Hands on them yet and impressions ? Thnaks Boris

AQ = Autoquad FC. One of the guys in Vienna is flying it and it is very impressive. From the systems I have seen it has to best position hold and for certain configs it also the most stable FC I have seen up to now ! But it's a calibration and setup orgy to get there at the moment ! Hope you...

Hi Yuri, mine is finished and working. Think copterworx is working on their own one. I am in close range they would have contacted me of they wanted to. Octocam in Vienna also has adapters finished for their setup so it's proof that it works and will be interesting to see how DJI reacts :) If...

not yet but heading out to my family now in a couple hours. Think its only going to take half a day though and they will be angry at me. Following copter schedule :) Test Gh3 on the modded zenmuse Get the AQ FC in the air finally More test with the Gopro 3 on my TBS and the new ground...

On a Caox setup there were a lot off guys especially with a MK Fc that mixed props, top bottom. Sorry about being so negative about it before, but i though you were mainly talking about flat configurations where I consider it to be more a hassle than bringing any benefit ! Boris

Thanks for sharing ! Gonna try that way instead of dual mode !

Dont get it. So ground station datalink to bt to bt iOS device. So one needs need power for the GS datalink ?

Since attitude gains mainly interpret the stick input from you TX have you looked in the assistant if there is anything weird going on with your TX RX setup ? Do you see the sliders in the TX config moving although they should be resting in the middle ?

In the video they state that it is connected to the micro USB port on the USB and that range will be 100 meter Bluetooth 4 or something ! Only way try to connect to that serial port on the USB device and bridge out to a better solution.

Well the one flying in the video seem to be a MK setup. But the reason could also be a PID running issue. But you are right a similar behavior with a WKM setup could be to high gains setting and oscillations kicking in !

srbell if you remember the pictures from some fairs, there were gimbals around with fs100 on them from DJI etc. And another test videos were seen in the forums with reds on them. So i am pretty sure that we will see something in that league pretty soon. At the same time a Gopro gimbal was seen...

What could be interesting is that you could be able to brake out an UART connection from this bluetooth module that is connected to the micro usb port. Use the UART get rid of the Bluetooth module and connect ti an xbee. Have an xbee on the ground and use a brake out board to connect an...

What systems do you have running WKM or MK ? And you are noticing similar behavior before take off ? Boris

Okay managed to bind two RX to the DC 16. One is a RSAT connected to WKM and one it is a R9 connected to the Zenmuse, no connection between the two Receivers. I managed to control both the WKM and the zenmuse. The only problem that I have is that the R9 restricts the whole setup to a 9 channels...

Jesus got it. It wasn't the beep+voice part. It was already there and i was frustrated, but the issue was the for my users there was no language assigned choose enlgish and it worked. No I didn't got the clone way i was under wireless modes/trainer and paired two RXs probably the wrong approach...

hmm just updated everything again deleted all old even the config files and went trough the whole procedure again. hmmm not working i will call them up directly and hope one of them speak german or english. Boris