Search results

I'm glad I found this thread. I am getting continuous yellow flashing which indicates lost radio signal. But I do have radio contact, I can even fly in attitude. Does anyone have a solution?

I have been using one of these, different brands of course, in different ways. Sometimes I take the circuit board out of the plastic box and shrink wrap it and sometimes I leave it in the box and drill holes for ventilation. However all of them give me that video drop out after two flights...

OK, I will secure and check connections and hot glue everything as a test. Yes, I took the converter out of the white plastic box and shrink wrapped it but it is open on the sides. I have an old Flux Capacitor (TM) that I am not using (just don't have the time anymore) maybe I will...

Bart, good advice and I can see where I can do it on the HDMI side but it is not practical on the Camera side, I would have to break off the glue each time I removed the camera. I will give it some thought. I should point out that in my tests I never got the drop out by touching and jiggling...

This one is really baffling me and if you have any insight it would be appreciated. This is the set up: Sony Nex7 HDMI out with Hyperthin cable to HDMI converter to Immersion 600mw Video TX. What happens is 70 - 80 % of the time I get an image on my ground station but then sometimes when I am...

After having the M10 for about 4 months I have decided it is overkill and too much gimbal for me. I purchased it used but in excellent condition with the expectation that many of my clients would want to fly larger cameras like a Red Epic. As you all know the M10 can handle cameras up to 12 lbs...

I was finally able to log in as admin and load and install the drivers with the MC connected. All is working now.

I've been told this is an old issue and applies to UHF and trainer mode

Did you get the box saying, "An administrator has blocked you from installing this app. For more information contact the administrator."

Yes, Windows 10. Yes, I know this has been confusing and I was using Futaba but I was having other issues with that FC so I moved to the A2 but then started having these issues. I still don't know what the problem is with the WKM but I am installing it on an HC800 and will do some tests. Can...

I can't connect to Naza M V2 assistant on anew laptop running Windows 10. The program is installed but is not working. The interface opens up but no connection with Naza. I thought maybe I need these:, DJI WIN Driver Installer, but I can't get the drivers to install, I get the message: This app...

It is all A2. Turns out it is the DX8 transmitter. Switched to a DX9 and works perfectly. Now another issue, can't connect to Naza M V2 assistant on another craft. The program is installed but is not working. Can't get the drivers to install, DJI WIN Driver Installer, get the message: This...

Yes, that is right. I have had issues with it but not specifically on the bench but flying characteristics that were unstable. It was suggested that I test it with another FC, but I think that is not the problem, the chances of two different FC causing problems is possible but unlikely. I was...

I am going to hook up another FC, I have a WKM that this A2 replaced. I want to eliminate the possibility it is the FC although I was having issues with the WKM.

Here's an update on my fluctuations problem. I replaced the entire power distribution system which is comprised of two copper buss bars and came pre-assembled from the manufacturer. No difference, still getting those surges and fluctuations. I thought of another test. I have three power...

Ahh, got it, thanks for the clarification.

I don't understand, it's the same basic design.

Even though they are round, the diameters are different so you cannot connect the the wrong way.

You cannot plug them together the wrong way, see photo They also come in blue and red so you can make the distinction if attached to power board or battery I love them, especially that you can solder the bullet when not in the plastic casing, you then snap them in with the tip of a screwdriver...

I replaced #2 motor, but did not help. It has to be electrical, you were right. The motor needed to be replaced anyway, there is definitely too much play in it. Next step is a complete rebuid