Search results

Yes , I am using some expo on yaw. It works very well, but my throttle is very touchy which is why I want to lock the altitude in so I can pan around for AP work. Because my radio is set up for airplane mode for MR ( I don't know enough about this stuff as to why) it does not offer me expo on...

Thanks "Old Man" that work perfect.!!

Anyone care to share there thoughts on a safe ( max ) operating range, line of sight, for a Spektrum Dx7s and Ar8000 receiver on a MR??

What's the difference between Buck converter and a step down module?? Is a Buck converter filtered? Is that what I want?.Can anyone recommend a module that will handle a Tarot T-2D, 400 mW transmitter and power/charge a GoPro 3 ( thru another step down to 5 V of course). Thanks guys.

Thanks guys for clearing that up!! Great stuff.

Hi All, I have 400 Mw transmitter to 7" offshore brand lcd monitor, Naza v2 with iOSD mini connected to Vtx. Running 4 cell with stepdown converter supplying all my accessories with 12vdc. Then I have another dropping the 12 v to 5 vdc for charging GopRo 3 black. Everthing works great till I...

In trying to resolve the reasons for a crash I had with my Tarot 680 I stumbled across something that everyone should know ( many of you might already.) The tarot , like many MRs have two centre plates. The power distribution board does not conduct electricity ( within the carbon fiber itself)...

Thanks RadioMikey, I am using a Tarot gimbal not the Zenmuse. I know nothing about an interference board. I will check into it.

Anyone know why my on screen data would be flashing rapidly from my DJI OSD mini, connected to gopro 3 black. Positive I have it wired properly. It is good and solid till I turn the camera on?? Rf interference from the gopro?? Thanks

I have just installed an iOSD mini with my Naza m-V2 with GPS. I am connected to a GoPro Hero 3 black. The problem i am having is I have my OSD info on the screen . I then power on the camera and still have the OSD info( but I don’t see my camera screen shot which I used to have before I added...

My hexacopter hovers excellent at the designated 50% throttle ( Naza v2 with gps) but very sensitive when I try to yaw for photo work. I read another post somewhere that someone had the idea of flipping one of my spare switches on my transmitter (spektrum dx7i) to set the throttle to 50 % while...

I have read that the " internal temp alarm" is a software glitch. Just ignore it.

Is your flight controller mounted with Tape or Velcro?? Try tape!

I too am having the same" travelling" when yawing. Hover is rock steady, But travels in a circle , clockwise when yawing clockwise and vice versa. I have balanced the props, checked that all motor shafts are mounted vertical ( looking for suggestions on how to do this more accurately than by...

I can get into cal mode without manual mode.! Would it be the latest naza software upgrade.?

ThANKS Bucker. Great stuff!

Stupid me. I did not have the satellite antenna plugged in to my AR8000. Everything good!

Thanks Steve. I do believe your right. My only hesitation ( or lack of knowledge) is that although I did have my receiver/ transmitter failsafe set to about 40 % throttle,9 for Multi-rotor) I have done a straight rebound of my receiver 2 or 3 times on the bench for my ESC calibration. Would...

I Just finished programming my new Hobbywing FF40 a ESCs. With each one separately plugged into my Receivers throttle channel to calibrate and do programming, when I finished each one I accidently shut off my transmitter first and the motor fired up to about 50% throttle?? When all connected to...

Well Im back up in the air again. Just to recap. Naza works good, Spektrum AR8000 works good, Gopro works good. Gps works good .Motors are good. Just had two ESCs smoking ,but I replaced them all just in case. And FPV transmitter went up in smoke.. My final thought as to the reason why?? I...