Search results

Verid... that's because .. if you scroll up this thread, you can see that Thomb posted: I reached him by email and asked him whether his Accelerometer Correction -> in the Calibration Tab, was perhaps Zero, or empty. And it was Empty. ( my fault !! ) This means that there was no accelerometer...

Hey Thomb.. nice location for testing.... where's that 'big mansion on an island' ;) !!LOL!! Thomb.... what about the twisted horizon on the Windmill shots .. is that intentional ?? or is that caused by something wrong before you had the Accelerometer Correction set to 3,4 or 5 in the...

Yes..will send you mail.

And at all others who have sent emails asking for swaps.... YES>>> I will get back to you soon, but I have a hefty backlog. I will, at least, be replying to your swap request emails,1 week before this backlog clears up, so that when sending your piclocs here for the upgrade, the backlog will...

@tahoelight -> AV320 gimbal is a PAN-> TILT -> ROLL gimbal. You should be running 3 servos all modified to 360 with pots disconnected mechanically ( so your tilt axis pot is to be disconnected mechanically ). The orientation for Picloc is to have the ARROW facing Forward or Back... ie TILT (...

Hi Ross... Yes indeed.... A 360 servo has a neutral point....the point where it stops turning. The best servos for stabilization normally have this point ( called deadband ) which is very narrow.... the best I've seen is 0.4uS !! The worst ones...as much as a Full FAT ... 8uS !! You must...

Sorry for the lack of current info. Masssssive headache yesterday fixing out last bugs. If I tried to re-shot the tutorial yesterday, I would have fainted. !! So it will be done this evening. Mag arrow - this should be pointing to the tilt axis, the arrow on top, the components on the bottom...

Yes.. you can still use it, but when panning very fast, you may notice some roll horizon inclination. In Calibration Tab, bottom item 'Accelerometer Correction', use item 5. The higher value in this selection, allows the accelerometer to correct quicker. These values are currently arbitrary...

PeterN, I totally agree with you about my bad comms lately. I've finally gave in, (and decided to give up my 1 year old smart phone) and purchased a good phone/tablet with an internet connection to be able to reply to emails on the go, and have my database with me. This should see things...

|One last remark... I really want to apologize for the bad timing in reply to emails. I have about 60 emails requesting swap ID's alone.... I will reply to these...don;t worry.. sometime soon. I have another batch of swaps being made right now. I wish to take the opportunity to... ..wish all...

Jesper, the way most people work if they have only the 5 channels afforded by the i1-i5 inputs, is to have 1-2-3 as Tilt roll pan, AUX 1 as E-Stop/home and Aux2 as Manual/AutoStabilization switching. If you have Spektrum, or are using a PPM-SUM output receiver, you can make use of the extra...

Shipped a batch today, and will ship another two big batches Friday and Saturday. Apologize for the wait. We're churning them out as fast as we can, however the calibration process is very ...very ...very time consuming. The internal foam insulation tape was not holding to expectation. So we...

OK... will look for it.

Thom... if you don't make it work, it is in my interest to get yours working well. This can be best done by a 15 minute Skype call, where I load special firmware into your Picloc, and I see the output from your DX6i. I was also sent a DM8 ( Spektrum module for Futaba ) and this is now also...

Thomb, Jesper, Really strange !! DX6i works perfectly here... see this clip ( save it ,then view ) -> CLIP DX6i does not have different framerates (like DX8).. AFAIK. Works on all power settings.... EU, France, and US. Perhaps, there is something different in the DSM protocol (both) your...

http://www.rotorpics.com/p3xv58_14/PiclocToolz_v58_14.htm This is the one shipping out with the new Piclocs....There is also a version for V1 Piclocs. The documentation for it is not ready yet, nor are the tutorial videos, however for starters, there is a link to PDF to get you going. This...

Hi, I will reply to your emails this evening/tomorrow morning. Very busy getting the new piclocs ready. I am just waiting for cables for the external magnetometer to arrive. They were sent with the wrong plug that plugs in the magnetometer board ! In the meantime, we're doing other assembly...

Many keens :) ..... there are only 200 upgrades.... 18% remaining to be swapped. send your ID swap request to the email a few posts up this thread. Somehow, I will reply.

Hi Guys. Apologies for the delays.. both in email replies and also for the sending out of piclocs.. both new and swaps. The manufacturer sent out all material but one component that is assembled here by me, was sent of wrong dimensions. I got these today and this weekend is going to be the...

Hi.. I've contacted my hoster to understand what went wrong. Thanks for your help Jozsef.