Search results

Ok thanks, now it's clear.

If i understand correctly: the second skyline you're referring to is the one that stabilizes roll so it's not rotating with the camera bed but it's fitted to the arc so that it rolls with it. Did i get it or shall i sue my english teacher? (again....:-)) C

I too would be happy to see a picture of that configuration if possible. TIA C

A few things lying unused around the workshop: FC 1,3 1 recom, 1x7805 130 Euro Navi 1,1 with Mag and flat cables 165 Euro MKGps 55 Euro 6xBL, 3 are perfect and working, 1 is working but has one strip torn off (the one without condenser look at the pic), 2 have unknown problems so total for...

Did you follow the update procedure? launch sw connect charge fw run update only then switch on skyline ?

Hello Micha, install back the 1.13, set manually the servo centers at the value "500", save (that is important) and the reinstall 1.16 or 1.17 It will stop reading wrong values for "value" and the sw will start correctly. Check it in the error dialog box: the value that makes the sw crash is...

I am stuck there too, the only fw i can use without knocking against this problem is the 1.13. I guess it's because i don't use an AV gimbal or servos (although my gimbal rotation range exceeds the AV's) so i keep filming with the 1.13. And am happy with the results, i must say....:tennis: Sadly...

Great! Can't wait to try it. Will we have back also the reverse servo tickbox? Thanks for the update! @Chris, really convincing video! Thanks for sharing your setup C

that was exactly what i was going to try this evening, yesterday i tried with two separate supplies (one for the rsgs and tilt, and one for the roll) with little benefit, now i'll set this up with more confidence. Thanks!

After trying it with both digital and analog servos (with some interesting results, i already wrote about it some 70 pages ago) i believe it is driving them around the 50 hz mark but hey! Who cares..it's just refreshing the very same fixed signal so it is not influent :-)

What about using something less wide than a Gopro? Just a personal preference in order to evaluate the results. Anyway: it looks good. Thanks and keep up with the good job!

I totally quote Nickville. @Darko: reduce the travel of the channel linked to the pan, and, if the radio allows it, also the throw of the trims (points per trim step). Then carefully set the center of the control. Just to give a reference my throw is at 6% and i have 1 point per step trim...

Hello Maurizio, answered :-) Cinestar is sold Thanks Claudio

...and THESE are the news i like to read here:tennis:

http://www.youtube.com/watch?v=0ITHa5ZaCHE Don't consider the post production (color etc). This is how my skyline behaves.

Hello, i found too that sometimes i loose the horizon. Hope it is something that can be fixed with the next fw. Also i'd like to have the possibility to point the camera upwards. I don't know if 1001copters had success in that but i didn't...whatever i tried i couldn't get it higher than the...

Please consider also that the problem can be at the other end, the pot one: the hitec 5085 (which never posed any problem with the rsgs) supply 3V to the pot so it is centered when it sees 1,5V whilst the 5625 and 5645 (difficult to set, in the end i gave up) supply only 2V to the pot, and...

When i found (10 minutes after receiving the skyline) what you figured to take out any servo electronics interference to the command line there was only one word i could think of: Respect. :tennis:

I am in Ponte di Piave, a city near Treviso. A dangerous one for any stabilization system as the city apellative is "Wines City" ..... :nevreness: I read the instructions thoroughly and for no reason i would ever have been able to follow these steps by guessing. Once done i am sure it will be...

Thanks for the good job! Here in Italy is a summer day early morning, and it's a shinyer day now:nevreness: