What type of computer windows /mac and if windows which os ie win 7 ,win 8 or win 10
You may have to disable the windows feature that stops unsigned drivers being installed in either win 8 or win 10
Take a look at this video it takes you through what you need to do and is much easier than me...
Well I have to give credit to DJI for their fast dispatch and DHL for their ultra fast delivery
I ordered 2 flight controllers from the DJI online store on Tuesday 06 Sept at 1.00pm local time in Australia
By 3.00Pm local Aus time I had a shipping notice saying the Item was to be picked up...
I found a work around by downloading it to my nexus phone and sharing it with myself using google drive and then installing it as normal
It seems to work just fine using this method
I have no idea what is up with my 3 pc's that I have tried 2x laptops and 1 desktop
Hello
I am trying without success to download the assistant for the Naza Lite from dji.com
BUT every time I click on the link to the download page for the lite I get a page popping up telling me I am running an old internet 6 browser and I need to either update my browser or turn off...
I would Really like to be able to get myself either a DJI Inspire or a Phantom professional or Phantom 4
If i was to win one of the above I would donate my QAV400 to one of the kids at the local flying club
I am running a T8fg super with an R6208sb receiver and I am using an sbus hub along with an sbc sbus decoder and operating a Naza on sbus 1-7 a video switcher on channel 8 and then 3 channels running my z1 tiny 2 gimbal all installed on my QAV520 V2 ( G10 520 mm arms )
So R6208sb into sbus 3...
I am currently using a Futaba T8FG Super I have had Spektrum in the past in my 3d heli days but much prefer the user friendliness of the Futaba
Currently using 11 channels oft he 14 Sbus Channels available via an Sbus hub and an SBC decoder on my QAV500V2 fitted with a Z1 Tiny 2 , 3-Axis gimbal
I had a V1 Naza that used to do this resulting in a very dead tbs discovery
I used the swift tap onto a flat surface with the Naza reset method and have since used this Naza only on cheap frames with cheap gear for line of sight operation at low altitudes only and mostly manual flight mode and...
Take the back off the radio and remove the ratchet from the throttle gimbal
It is only a thin metal strap held on with a single screw
it may even be smooth on one side so it can be flipped over and replaced to allow a steady amount of stiction with out the ratchet / notch
This task is not...
do you live within the restriction zone near an airport
Not too sure about how close to an airport I think 5 km's may be the linit to major one and the Gps will prevent you from flying in any mode other than manual or ATTI
I thought the Gps needed to be unplugged to work around the airport/gps...
A 5000 mah 20c battery is actually 100 amps
5 amps x 20c = 100 amps
series = doubling of voltage amps stay the same
parallel = doubling of amps volts stay the same
I would think you would need at least a 40c battery to run an octo copter under full load
I run 45c-90c burst 4cell 5000 mah...
Assuming that it is all setup correctly in the radio and the calibration has been done both in the Assistant and the compass calibration dance
Have you armed the system with the CSC ( control stick command ) as in both sticks to bottom center of the controller
This is done once the GPS has...
So no upgrade at all to the flight controller firmware just a new shell for the assistant !
I sold my Naza lite and may be soon doing the same with my upgraded v1's ,time for a change and have been playing around with KK2.1 and cc3d boards
No updates for the lite version yet (maybe never ) and it does not support the v2 pmu according to the DJI website
The lite will behave better if you let it sit on the ground for a couple of minutes longer after it locks the GPS
Some get marginally better results with unplugging after the GPS...