Search results

What type of computer windows /mac and if windows which os ie win 7 ,win 8 or win 10 You may have to disable the windows feature that stops unsigned drivers being installed in either win 8 or win 10 Take a look at this video it takes you through what you need to do and is much easier than me...

Well I have to give credit to DJI for their fast dispatch and DHL for their ultra fast delivery I ordered 2 flight controllers from the DJI online store on Tuesday 06 Sept at 1.00pm local time in Australia By 3.00Pm local Aus time I had a shipping notice saying the Item was to be picked up...

I found a work around by downloading it to my nexus phone and sharing it with myself using google drive and then installing it as normal It seems to work just fine using this method I have no idea what is up with my 3 pc's that I have tried 2x laptops and 1 desktop

Hello I am trying without success to download the assistant for the Naza Lite from dji.com BUT every time I click on the link to the download page for the lite I get a page popping up telling me I am running an old internet 6 browser and I need to either update my browser or turn off...

I would Really like to be able to get myself either a DJI Inspire or a Phantom professional or Phantom 4 If i was to win one of the above I would donate my QAV400 to one of the kids at the local flying club

I am running a T8fg super with an R6208sb receiver and I am using an sbus hub along with an sbc sbus decoder and operating a Naza on sbus 1-7 a video switcher on channel 8 and then 3 channels running my z1 tiny 2 gimbal all installed on my QAV520 V2 ( G10 520 mm arms ) So R6208sb into sbus 3...

I am currently using a Futaba T8FG Super I have had Spektrum in the past in my 3d heli days but much prefer the user friendliness of the Futaba Currently using 11 channels oft he 14 Sbus Channels available via an Sbus hub and an SBC decoder on my QAV500V2 fitted with a Z1 Tiny 2 , 3-Axis gimbal

I had a V1 Naza that used to do this resulting in a very dead tbs discovery I used the swift tap onto a flat surface with the Naza reset method and have since used this Naza only on cheap frames with cheap gear for line of sight operation at low altitudes only and mostly manual flight mode and...

Take the back off the radio and remove the ratchet from the throttle gimbal It is only a thin metal strap held on with a single screw it may even be smooth on one side so it can be flipped over and replaced to allow a steady amount of stiction with out the ratchet / notch This task is not...

do you live within the restriction zone near an airport Not too sure about how close to an airport I think 5 km's may be the linit to major one and the Gps will prevent you from flying in any mode other than manual or ATTI I thought the Gps needed to be unplugged to work around the airport/gps...

A 5000 mah 20c battery is actually 100 amps 5 amps x 20c = 100 amps series = doubling of voltage amps stay the same parallel = doubling of amps volts stay the same I would think you would need at least a 40c battery to run an octo copter under full load I run 45c-90c burst 4cell 5000 mah...

Finally ! A ride on leaf blower

Assuming that it is all setup correctly in the radio and the calibration has been done both in the Assistant and the compass calibration dance Have you armed the system with the CSC ( control stick command ) as in both sticks to bottom center of the controller This is done once the GPS has...

So no upgrade at all to the flight controller firmware just a new shell for the assistant ! I sold my Naza lite and may be soon doing the same with my upgraded v1's ,time for a change and have been playing around with KK2.1 and cc3d boards

No updates for the lite version yet (maybe never ) and it does not support the v2 pmu according to the DJI website The lite will behave better if you let it sit on the ground for a couple of minutes longer after it locks the GPS Some get marginally better results with unplugging after the GPS...

where are you someone may be local and be able to help point you in the right direction and help you along Take a deep breath and retrace all the steps in the manual and watch all the videos on http://www.dji.com/product/naza-m-v2/video for the Naza and then read the manual again and again it...

Glad you got it sorted ,Nothing more annoying than a completed model sitting on the bench and having a not so obvious fault stopping you flying Have fun

Well after reading the manual I can only see that you may have to recalibrate for the GPS and make sure that you are facing absolutely north away from any sorts of possible interference Even a set of keys or cellphone in your pocket or a watch could make a difference I even take my metal belt...

I have had 2 Blade 3d heli's that flew perfectly for a handful of flights and then started doing strange things opposite of the given commands both were found to be faulty and were replaced with new units no hassles and both still fly great to this day One is a 450x heli and one is a blade...

As the title suggests I need a flash tool for a H/King KK2.1.5 and as usual hopeless king are out of stock So out of these 2 which should I buy being new to this type of flight controller I have no idea on what to buy or how to flash a board like this (it took me 2 hours to get my gimbal...