Recent content by Go4d

Hello Fltundra, In regards of motor alignment, it only has an error of 0.4-0.2 degrees in just one of them (M2), other 3 motors (M1,M3 and M4) all have same degrees with an error of 0.1 to 0.2 degrees (1/10th of one degree),…. I don't think that I can get them closer to a zero, this because I...

Hello Guys, I did some new flights, here is the result… I double checked props and they were very well balanced, then I checked motor alignment as Kloners video, at first site they all looked aligned, but for my frame I tough that it was not so precise, so I did a 4 point calibration using an...

Hello Guys, I did some new flights, here is the result… I double checked props and they were very well balanced, then I checked motor alignment as Kloners video, at first site they all looked aligned, but for my frame I tough that it was not so precise, so I did a 4 point calibration using an...

Thanks Fltundra, I will do some test with default settings on the ESCs. About the props I did check balance and they are well balanced, I checked with two balancers and they are both showing balanced props, so I am ruling out a prop balance problem, I already re-checked them. I will do a motor...

In regards of the KDE ESC's programming: - I adjusted the S.R. BRAKING ACTIVATION to "PRECISION", I was told by KDE that this will immediately enable the braking to the highest-level (maximum control of acceleration and deceleration). It will make the multi-rotor feel "robotic", meaning very...

Hello Fltundra, Thanks for your advise, the props are well balanced I did make sure of that before flying, however I will double check just to make sure…. The motor mount level I did not checked, I guess I thrusted Xaircraft frame to be well align, I will check motor alignment and let you know...

Hello Motopreserve, Thanks for your advise, the props are well balanced I did make sure of that before flying, however I will double check just to make sure…. The motor mount level I did not checked, I guess I thrusted Xaircraft frame to be well align, I will check motor alignment and let you...

Hello Guys, I did some testing, and I need some advise, This is a smaller quad that I have, I have not yet done test with the big quad, but I will like to get this one tuned first, still working on the big one…. This is a X650 with SuperX, KDE 2814-775 with KDE ESC 35, 13x5 T-motor prop. I did...

Hello Guys, I did some testing, and I need some advise, This is a smaller quad that I have, I have not yet done test with the big quad, but I will like to get this one tuned first, still working on the big one…. This is a X650 with SuperX, KDE 2814-775 with KDE ESC 35, 13x5 T-motor prop. I did...

Hello FLTundra, I am going to do the update on the ESC's with the new firmware, I will post when I do some testing.

Hello FLtundra, Sorry for the late reply, I was traveling and could not get back to some "quad action"…..I have been doing some new tests, already double checked setup, props balance, and also I have another smaller quad, having same issues, I think that my problem is the KDE ESC that it is not...

Hello Guys, I wanted an advise on what ESC to use with KDE motors and SuperX,... what ESC other than KDE ESC's are recommended for this combination? I have read on this discussion that there has been know issues with KDE ESC's and SuperX, and some people were using T-motor… I have been doing...

Hello FlTundra, I do know what you are talking about, that is why I am asking for some interpretation, I want mine to look like yours, by the way they look pretty nice, I want to tune mine to make them look better. I am not sure if the problem is from the gains or if I have a problem with an ESC...

I also have the dubro, props are good.

I am using CF T-motor, I have a magnetic balancer., For motor alignment I used a rig with digital inclinometer. Any other ideas? thanks