Aeronavics / Droidworx CX600 build

[nicwilke]

I'm using the Xaircraft SuperX, so it's a little difficult to compare. You should get around a kilogram of thrust per motor at 75% throttle, so if your all up weight is about 2kg, you'll have a good rig if you tune it in well. Try changing gains up first. Go in 10s, and set and fly record on paper the settings, followed by results. Don't fun fly, just up, hover, land. And write down a result from 1 to 10, 10 being perfect and 1 being wobbly. I know it sounds clunky, but yoy will always have a point where you go to far, and then you know from your writings what setting yoy can jump back to. Good luck

Sent from my GT-I9305T using Tapatalk

 

[koptercam]

Thanks a lot mate!
My all up weight is 2.7kg and still got the GoPro Zenmuse to go on, so will probably be around 3kg when all said and done. Maybe i might have to jump to 12 inch props.
I'll play around with gains as you mentioned... might see if i can get indoors somewhere so i don't have the wind factor to consider either
Thanks again for your advice!

 

[nicwilke]

Here's how I mount my gimbal now. Custom made carbon fiber mount.

Sent from my GT-I9305T using Tapatalk

 

[nicwilke]

Sent from my GT-I9305T using Tapatalk

 

[nicwilke]

Sent from my GT-I9305T using Tapatalk

 

[nicwilke]

Sent from my GT-I9305T using Tapatalk

 

[nicwilke]

Sent from my GT-I9305T using Tapatalk

 

[nicwilke]

Sent from my GT-I9305T using Tapatalk

 

[cbpagent72]

Sent from my GT-I9305T using Tapatalk

Is that a Tau Flir camera above your GoPro?

Sent from my SPH-L720 using Tapatalk

 

[nicwilke]

No, it's a fpv camera. Probably won't use it much, but it's hooked up.

Sent from my GT-I9305T using Tapatalk

 

[nicwilke]

Here's my new gimbal and battery mount. It holds a 3 axis gimbal for yaw smoothness.

Sent from my GT-I9305T using Tapatalk

 

[SleepyC]

This SuperX is seriously the best flight controller I've ever flown. Yes, best. It is so stable, and flys fluidly. I'm used to Naza and ZeroUAV YS X6, and this thing is incredibly good.

100% agree. It is so much better than anything out there for the smoothness and feel.

 

[nicwilke]

Sleepy, I have a basic and a pro. Both faultless.

Sent from my GT-I9305T using Tapatalk

 

[SleepyC]

Sleepy, I have a basic and a pro. Both faultless.

Sent from my GT-I9305T using Tapatalk

Yea, I have a (1)basic, (1)standard and (2) pro ( changed all my rigs from Hoverfly) and they have been amazing. The only thing i had problems with was trying to put on on my XY8 coax, it did not like that config, but the engineers sent some ideas, but honestly that rig flys so well on the HFP I’m just leaving it and hoping the GPS gets better. BUT any new rig I build will get a SuperX... so easy to set up and so consistent. I have a similar go pro rig as your CX600 (just a quad frame us version, but all good running gear) and i have around 55 flight son that rig now, and it’s been FLAWLESS.

 

[nicwilke]

So excited to test this in the air tomorrow. No slop on the mount, its as rigid as hard mounted, the only wobble is from the actual anto vibration, as per normal.

 

[Michael64]

Hey Nick what motor did you use for the Yaw axis, and which three axis board or you using.

Michael64

 

[hacksaw44]

Great set up !!

 

[Cuba59]

Hello, Question,
how easy is it to mount a Zenmuse 3D on the CX600? is there enough "material" on the centerplate to attach it?