Search results

I got skyzone goggle and futaba 10c with ch Rx and head tracker need help configuring the skyzone with my head tracker to make it work . is any one using head tracker with dji naza thanks in advance

I have encountered a strange problem. As I was doing some long flights today, I noticed that suddenly the Hexa yawed to the left and left stick input had little influence. Basically - giving full left yaw only stopped the right yaw movement and at least it was possible to land the machine...

I made a new quad copter today but the copter is keep turning to the left it does not stay straight need some help

I got a Dji Naza V2 and I made an Octo but the F1 in controller does not start the motor I tested the 7 1 esc by connecting it to f2 and it did work perfect so it is not the ESC but not the F1 and when I connect the battery i see that power goes to the F1 controller port and turning the ESC...

Heloo i recently overheated my xaircraft motor and damage they still work but not that good want to replace them can some let me know where to find them it is v8 version first one thanks

Heloo guys if some one can help me in my gs software shows motor balance (turn the motor imbalance 150 and my motor does not start but when i raise the throttle 100% then the motor keep beeping but if it is lower no beeping and does not start make me go crazy

my tiger esc does not stat how to reset it it could be in safty mood it is tiger ESC?

I just build a DJI Naza M Quad rotor and it wobble and cannot be controlled I thighten all the screw to make sure there is no vibration which i think there is not but still wobbling heavily some one suggested that it could be the gain does any one suggest anything else...

I just build a DJI Naza M Quad rotor and it wobble and cannot be controlled I thighten all the screw to make sure there is no vibration which i think there is not but still wobbling heavily some one suggested that it could be the gain does any one suggest anything else...

I got some 30A T motor orange ESC cannot be calibrated I could not found any tutorial for it as watched some other peopel doing it to some other kind of ESC I turned on the TX and left the throttle to highest then connected esc to port 3 of RX then plugged the battery and after 4...

I built an Octo with dji naza and got Frsky x8R sbus need to connect my servo gimbal since all ports are taken by ESc is there any way to make this work i read back then that it is possible doing a bypass thanks

i just try to fly my wKM 2.5kg without battery and 3.5kg with battery and i use WKM v2 IMU but my hexa was rotating slowly without me doing anything when it was up how should i fix that any idea thanks

Hi I just updated my WKM IMU 1 to IMU2 but when it is in GPS it does not hold postion and also when i left off if i i do it in GPS in try to flip backward it was not like that in WKM 1 which was holding postion and not tring to fli my hex copter weight is 3kg without battery with one...

Hi I just build a copter total weight without the battery is 3kg i just want to get a battery so what battery is good the site that i bought the motor and ESC recommend 5s -6s for this motor and ESC but i just want to now if i use 3s or 4s should be OK

i need help regarding the connections i know for the wires there are AWG # since i want to connect the ESC to Power distributor so is there any certain size of bullet connecter that i have to use or does not matter and i can use any kind thanks again

heloo Guys I need some help need Power Distribution for my hexa weight 3.500 kg without the battery and got 40a ESC and 460 kv motor using 4s and 6s lipo also building a octo with 8 motor using 30 A esc and 960 motor using 3s-4s lipo i found some Power Distribution in Hobbyking but it ist only...

Can some one tell me what What Gauge is the Wire in xaircraft 650 v8 motor i need to extend the wires since i got a 30 a ESC that i want to connect that can some help plz thanks in adavance

I just finished my Octo copter using X aircraft motor RC timer ESC and naza M and since the wire was not long enough i bought some extension wires and that wire was not good enough for use with 4s and 3s battery since it got hot and smoked and crash my copter any suggestion what...

Hi guys I finally got my Octo with 8 xaircraft motor and rc timer 30a with Naza M to run and tried to calibrate since all the motor does not start at once they are simonk ESC and when i do ESC Calibration by connecting each ESC to throttle port of RX and then placing the throttle...

can i use wokong M OSD V2 with Naza is that gonna work