Search results

Hi Bob, Your welcome! Horizon hobby said that if yours is one with the issue "hold" means the Tx will drop the transmission sometimes to the Rx, which will trigger a failsafe and in your hexa's case she should just land.. It looks like the identifying code is in the battery box of the Tx, see if...

Hi Bob, Sorry for that... my Tx is so different from yours in how the menu works.... I was trying to find out how your switches are assigned and to what channel so I can figure out the aux1 to naza x2 mystery. I think that the key to all these issues lies in how your Tx is set up (switch wise)...

Hi Bob, There is but it is only a simulation in the assistant, but if it works in the assistant it should work... Get the hexa hooked up to the assistant with your Tx on and binded toggle the green switch on your Tx to show you are in attitude mode on the assistant screen that shows the control...

Just out of curiosity what ports on the naza does gear and aux1 go to from your Rx?

I found something that may be related to your hexa not holding the bind, try this first to see if it will hold the bind and do the loss of Tx failsafe... according to horizon hobby manual For the low thro. stay above 10% or shes coming down (motors will shut down), in the picture you could do...

Well this good news!!! The failsafe part is not to hard to do, I have to refresh myself on it but heres the thing... you maybe have to redo it every time you lose the bind.... I think..maybe... but maybe not. I'm going to read up on it again, then get back to you.... but for sure you will have...

Found this video on DJI, looks pretty easy to follow.... hope it helps... http://youtu.be/sWWinX3m23A

Bob, Your welcome! I found a explanation for error 26, it does not say OTHER but here it is... error 26= "please perform advanced calibration" .... So going with that I assume it means the IMU and there is a advanced tab in one of your screen shots..... but before we go there.... from the time...

You can get the rapid red VU flash when your battery is getting NEAR the threshold for low voltage protection and the motors are pulling hard (wide open) also a cheap battery or a battery with a low c rating or a c rating that is inflated.... As for the rapid ascent around 50% thro. the only...

Alright lets see what dji has to say..... let me know.

When you try to start the motors are you still plugged into the assistant? they won't start if you are.. Also did you power down the quad after using the assistant then power up and try to start the motors? Did you come across a screen for motor idle speed? and is it set to recommended? Also if...

Home early due to late winter storm.... Too bad for the moose's... It sounds like she's ready for flight, glad to hear the Tx cali went well if you like you can change the cut off type to immediately then click write to send it to the naza (this is what I use) but read up on it in page 16 of...

This is good...this is very good! So you say that the monitor values are fluctuating? if you mean the sticks monitor they may quiver a bit but thats ok... as long as they move in the right direction when you move the sticks and it sounds like they do. If your talking about the IMU portion thats...

I will take a look at the phantom manual tomorrow, this may be as simple as a fresh reload to get things up and running... and I think it is. Try one thing ether tonight or tomorrow morning, see if you can get the Tx to bind to the Rx.. not start the motors and ignore any colored lights from the...

This is going from bad to worse..... IMU screen don't worry about that yet and you may not ever have to. The Tx screen is a war zone right now unfortunately... the last shot shows full throttle and sticks hard over... not good! If you did not try to make any adjustments with the phantom software...

Hi Bob, Here is what horizon hobby said: The slow flash in the Rx after powering down the hexa only not the Tx , IS NORMAL... it is the Rx saying who turned out the lights, but it is still binded. So Langdale is correct, it is just the Rx saying where is my old signal???? (how h.h. put it) The...

Hi Bob, Take a look at the manual there are a few versions of "the secret handshake" page 16 try them, if you do them too quickly she won't start... Nice screen shots!!!! The shot of the gains is that where shes at now? Waitin to hear from horizon hobby I'll post more in a bit...

Hi Bob, Ok I got it now, so based on what you've said it sounds like you have a Rx issue... The Rx still recognizes the Tx when you you power down the hexa and repower, but when the Tx is turned off also then it goes blind (the Rx) and no longer is bound... I'll put in a call to Horizon support...

You are correct about attitude and manual modes... It is very strange you have to keep on re-binding, I thought you said it was staying bond but the Rx was giving a slow flash? You could try moving one or both of the Rx's, they are supposed to be turned 90 deg. to each other and as far apart as...

Good point Langdale, when you unplug the multirotor then turn off the Tx (normal procedure) you are cutting power to the Rx, so your saying that if a person leaves the Tx on and powers down the multirotor and then powers on the multirotor the Rx will read this as a loss of transmission or a loss...