Search results

  1. Dreamweaver

    PH Hero 3000 gimbal "caught on film"!

    Retractable landing gear as well...nice
  2. Dreamweaver

    F450 retail space.

    In the middle is the WKM power module...bottom GPS led. Fitting a WKM, DL, FPV and CAM on a stock 450 frame is tough fer sure. UPS delivered my FPV pelican last night i went with a 1400 to keep things nice and compact as i also plan on using this for a target cam when i shoot at 300-1000.
  3. Dreamweaver

    F450 retail space.

    Rev. 3 with gains for RPV @ 200 and ATTI @ 110 handles nice again. Hope the antennas don't freak each other out.....will test data with FPV tomor.
  4. Dreamweaver

    F450 retail space.

    On the bench the side with holes was the hotter...also thought it would be better for it to breathe this way. In the remaining channel there is the DJI data TX. How do you stop the antennas vibrating down from vertical?...would one up one down work best? Got the new JVC action cam...but dont...
  5. Dreamweaver

    F450 retail space.

    One is the 900 datalink the other is the 1.2 FPV. Don't know much about transmission will they work better vertically? Also which high dB antennas are best bang for the buck? ~Mike
  6. Dreamweaver

    F450 retail space.

    Thanks for the thoughts kloner... i went back to the drawing board this morning. Here's Rev. 2 however all the old clutter was 'only' 150g...i guess when you approach the thrust limit of the 450 every gram counts. Still feels sluggish but is better...will increase the gains to see if i...
  7. Dreamweaver

    F450 retail space.

    Well i finished my FPV install without using a second lower and i think i might have over done it. Added 250g (the 2 lower levels of gray channel) the channel only weighs 10g per inch btw. Total weight without bat is now 1,450g with bat 1,700g and it seems to be struggling even with the...
  8. Dreamweaver

    Worth a look.. Motor Connectors on DJI Motors

    He might have caused it by pulling them out for repairs...if he never touched them since intial install then yeah that sucks. Just did all of mine when i swapped in some Tigers. ~Mike
  9. Dreamweaver

    Dji datalink

    Awesomeness...but will no doubt be major bookoo :dread: Ruling R/C TX RULING-MULTI-FUNCTION GROUND CONTROL TERMINAL FOR UAV/UGV The Ruling is DJI's revolutionary multi-function ground control terminal. With the Ruling, users will not only be able to control an unmanned aerial or ground...
  10. Dreamweaver

    F450 retail space.

    Hey has anyone installed another lower plate via spacing studs to gain retail space for FPV/Datalink mounting? Seems to me this second lower plate would not only add space but also provide protection (skidplate) and provide 4 new power point sources is you looped in the powder from the other...
  11. Dreamweaver

    F450 Motors still getting hot

    3S or 4S?
  12. Dreamweaver

    WooKong M--White Flashes???

    Is DJI working on a retro kit to stop the white flashes? Other Mounting MethodOf course you can also use other methods to mount the GPS module, such as: Use the 0.2MM double-sided copper-clad boards to make a double layer shielding Connect the shielding to the cathode, make sure the two...
  13. Dreamweaver

    HoryzonHD 2 Review

    Is the UHF kit required to work with a 2.4Ghz TX or 900Mhz datalink? Pic quality seems to be superior to all the other FPV choices, would you go back to a SN555/777 or WDR770? Any idea of the V3 ETA...will it have better buttons and a no LCD option? ~Mike
  14. Dreamweaver

    8" & 9" Graupner prop prep

    I thought the 8s and 9s were 6mm or something?
  15. Dreamweaver

    8" & 9" Graupner prop prep

    A drill will generally be oversize...how do the props feel on the motor shafts any freeplay? There's alot of junk reamers out there...however there is one company that makes a nice one...i've got one at home but not used it yet as i'm still using the 10x5's. Got mine from Amazon this is it ...
  16. Dreamweaver

    Dji datalink

    Yes...magnetic north adjustment it's 10* where i live...google it there will be a calculator for your zip. Makes it flight straight and reduces/eliminates toilet bowl effect in hover. ~Mike
  17. Dreamweaver

    Dji datalink

  18. Dreamweaver

    10 x 5 Graupners onto DJI550

    Your call. A couple of people claim to be flying like this and have had no issues....but to me it looks like the nut is resting on the crushed lettering. If this was to slip the prop would loose all drive and anything other that a hex would drop like a rock. Here a pic of the bevel as...
  19. Dreamweaver

    Dji datalink

    I still do and did auto the very first time....just have the TX in hand to flip it to ATTI mode until you get used to it. You do have your mode switch, RTH mix and failsafe all set up and tested right? Direct manual ink...
  20. Dreamweaver

    10 x 5 Graupners onto DJI550

    Get the least angle you can...45* is good. Contersinker + cordless drill + safety glasses...just go bit my bit the DJI nuts are aluminum so it's easy work...don't go too much...just enough. To check hold the prop and nut up together and get it so it's just bigger than the prop hole diameter...
Top