Search results

Got a few Brand New in the box Phantom 4 Batteries. Asking $150/each shipped.

Looking for 2 KDE UAS 55A ESC's. Thanks

looking for KDE 4014-380kv motors. let me know what you have. Thanks

Is this still available? I can't seem to send you a PM, can you send me one if it's still available?

Sent ya a PM.

dang, that was a good deal. They had the 3510 475kv for $65ea. Too bad they don't have anymore.

Those KDE's look nice.... but they're sure pricey. I'll consider them if I can't get this motor/prop setup working well. I replaced the dampeners with standoffs, it appeared to help, but I was flying in a gusty wind for the first time. It was solid in the wind. I didn't get a chance to do a...

I wish! Since this is my first coaxial, i wasn't quite sure what the flight times would be. With a zippy 6s 8000 and an AUW of 4.8kg, I'm only getting about 8:20/flight. However, I tested with 2x 4s 10,000 and got 20mins. But the avg motor usage during hover was 86%, which is too high. I was...

Hi Mike, Thanks for the comments, I just realized I made a typo in my original post and mentioned 12x6.5 on the bottom. It's supposed to be 13x6.5". I'm going to spend some time today and balance the 13x5.5 and 14x5.5 t-style props and see how it flies. I agree about the battery plate being...

I agree, I grabbed the leg during a hover and I could feel a faint vibe. I went through one quick round of balancing before flying and skipped the hub on half of them. I have a set of t-style props 13x5.5 and 14x5.5 I'd like to try on it. Going to get a good balance on them and see if the vibes...

It's amazing how useful the logs are. I also have a v1 naza and once problems occurred, it was hard to diagnose. If they supplied logs, it would be soo much easier to tune up your rig. I think i'm converted now. Going to sell off my dji stuff and get another SuperX. It just flies soo much...

the motors were pretty off, so much for trusting the indexed marks. lol. I squared up the top motors, on the bottom motors, some of them are a little off. I did the best I could without shimming the motors. http://log.xaircraft.com/report.htm#2014_09_19_193103.250_39.1.07.14 I think I have the...

I'll have a look at the motor alignment and see how off they are. Hope the level on my phone is accurate enough.

lol That's because the skids are angled and causing the rear to droop. It's not like that now. The skids are straight now. I can only imagine the amount of prop strikes I might get if I flew it like that.

yeah, that's what I was thinking. Unfortunately there isn't a ton of room on top to mount any batteries. I'll try mounting two packs to shift the batteries more forward to see if it helps.

If you have a look at this guys (kcsajtai) log on his Y-6, his motor outputs are more even. The top props are 28% and bottom are 38%, where as mine is alternating between top and bottom per arm. http://www.multirotorforums.com/showthread.php?13158-SuperX&p=148436&viewfull=1#post148436...

Looks like you have a quad configuration though and not a coaxial. I'm trying to verify that this isn't related to it being a coaxial.

The gopro and battery are on opposite ends. But I think part of the problem is that the battery isn't close enough to the camera and is acting like a lever, exaggerating any little movement it sees. If i'm flying slow, it's pretty smooth. I attached some pics of the rig. The battery attaches...

I just got a superx and installed it in a trooper Q700 in an x8 config. I'm currently running into some issues with vibrations/oscilaltions in fast forward flight. This is evident in the brushless gopro footage. I currently have the att gain set to 20% and i'm trying to dial it in by changing...

Bart, Are you still selling these? Any other good alternatives?