Search results

Hi all, I have an A2 hex that I slapped a Zenmuse H3 GoPro gimbal on. My problem is no matter what I try, the horizon is off a few degrees. I know its not the gimbal as the same parts work fine with a Naza V2 I have on another rig. I have tried IMU cal multiple times on the A2 with no luck. The...

So the other day I was looking on the dji site and under the Wookong M it said "not available in your region" today I looked again and it said "404 error page not found" whats the deal with that??

Zenmuse H3-3D "Phantom Version", is the only difference no GCU? will the cheaper "Phantom Version" accept the ribbon cable from the GCU and thus work on a non Phantom? thanks!

Hi all, I've been flying the E800 "tuned propulsion system" Very smooth power super quiet. I actually hit 57mph forward flight speed with this system. I am currently not using the "active braking" feature because I am running the props from the former E600 system due to clearance issues with the...

Hi all, I just finished a hex build using the E800 system from DJI. First off these are the most quiet motors ever! Now for the problem.. Power it on ESC's sound off, all esc led's good, take off, fly's awesome. Now the problem. Once I land if the flight battery is swapped out, or even just...

Looking to purchase asap. Must have fixed tripod gear and be mountable to a SkyJib frame. Not particular on brand as long as it works well. DIY style is fine as along as it's been sorted out. Would prefer a Southern CA seller, cash in hand for the right gimbal! Thanks Jeff

So I'm not sure, where I should really have these set. I'm running the DJI E600 system on an AUW Hex of 7.5 pounds. I pushed it the other day and got a 30 minute fight time, however I put back like almost 8700mah on the recharge of the 10000mah so I assume I'm taking them down too far. It's...

Can someone enlighten me on the benefits connecting Sbus or Dbus Vs "traditional" which is how I have my Naza V2 hex setup with a Futaba t10j. Thanks, Jeff

Not sure if this is the best place for this. I installed an zenmuse HD3d GoPro gimbal, Not on a phantom but on a Naza V2 equipped Hex all works great looks great, I can tit bla bla bla, However I cannon adjust the max and min angles like I could in the Phantom version, and It shows a padlock at...

So far I wet sanded the dji logo and used a black sharpie, looks better than orange and white. GPS signal has not changed a bit. I was now going to give it a light coat of flat black spray paint and test signal, Does anyone see this as being a problem? Thanks in advance.

Just got this email from DJI <tbody> <tbody> Dear DJI A2 Dealers&Customers, In order to secure the self-tightening propellers, A2 2.4 firmware will initially allow the motors start off at a higher speed, and then slow down back to idle speed at the beginning. However, some customers feedback...

Ok granted this is my first Naza V2 setup, I've done A2's and WKM's I've adjusted my endpoints for my 3 pos switch for GPS-ATTI-ATTI all hit the blue marks fine. I then turn off the Futaba T10J and nothing happens. I'm not that familiar with the T10J I was reading in the manual about "failsafe"...

I used the GoPro app, and it did some weird stuff, check out the front right motors, I promise, they don't wobble in real life:shame:

Im baffled here, I understand how to assign it, however everytime I choose "ST-THR" ON: UP 50%. When I try it the timer starts only when i move my pitch and elevator stick, but once centered the timer stops. The aircraft flies correctly and all controls are good in the A2 assistant. How do I...

All went well, perhaps a bit too little weight onboard as it wanted to fly as soon as I armed the motors! so I either need to drop the idle below the recommended or add more weight. The GoPro is hard mounted and will be for fpv only.. Sorry for the bad ground camera work, it was a friend who's...

Wow these KDE motors sound amazing, and sure move some air. We bagged it with a ton of weight to check control inputs.. all good so far..

I get the premise. But does one use regular hot glue as in glue gun? I've seen many factory electronics with hot glued bits so I assume it's ok.. Thoughts ? Kloner?? SJX8 Is now running:-)

Hi can anyone recommend a quality prop 18" x 6.1 in CF other than the T-motor ones for $120 a pair? I need two full set of 8 Thanks in advance!

For sale 8 brand new in packages Maytech 65amp OPTO HX Simon K firmware ESC's. These are brand new just in from China.. I have two sets of 8 keeping one set, selling the other. These are the latest Simon K firmware and were shipped to me the first week of October 2014. I have the original...

I have my Futaba 10CHG all setup with my A2 for my SkyJibX4 (X8) very similar to the phantom in "Naza Mode" control switches. So would it just be a matter of copying the model I use for the SkyJib, and name it Phantom, then bind to my P2 and do normal stick cal in P2 assistant? I prefer to have...