Search results

If this has been addressed I do apologize... My quad 550 is spinning on takeoff but level, not flipping over. All the trims are zero and the quad has been calibrated. The spinning is quick fast.. I wish I could take a video but dont have a third hand to record the video.... is there a solution...

Thought I would ask about it. I could buy a RTF package for the $300-400 and play with it... I might try it out and will give the results.

Quick question in regards to this posting... Im looking for advice on a setup to buy for my kids. I have a Spektrum DX9 transmitter and like using it. If I purchase one of the RTF packages (say helipal.com) that comes with the TX and RX. I would like to use the DX9 and a Spektrum RX replacing...

Have a quick question... I have been experiencing the same issue of taking off and my quad drifting to the right. I have tried to calibrate the sticks and the quad several times. I have tried each time with the quad in GPS mode.... Question: How does the gain setting from the Spektrum TX...

Hey everybody here... some good news to report... the quad is not arming the motors and all is "running".... Had to swap out the Spektrum AR9020 for a Spektrum 8 channel reciever... Im sending the 9 channel back to see if its defective. I did all the calibrations including the dance to spin...

Thanks all with the help. I will highlight some of the equipment again and highlight the issues along with some work I have done. the transmitter is a Spektrum dx9, with a AR 9020, the XA controller, KDE ESC UAS 35, dualsky xm4010mr-6.5, all powered from a power distro board... The ESC's and...

Thank you Motopreserve.... I sent a note to KDE and XA.... The beeping happens whether the KDE ESC's are plugged into the XA FC or are not plugged in, if this makes any difference.

The beeping is coming from the motors Dualsky XM4010MR 6.5. I checked the throttle on the Spektrum DX-9, the settings are -100 and 100 linear. From reading the KDE ESC do not calibration. I looked around why motors continously beep and many people said it had to do with the throttle settings...

Im having an issue with my quad XA Controller with KDE ESC's. I bought the KDE ESC to replace the Spyder OPTO ESC that would calibrate but not arm after many changes in the setup and many attempts to calibrate the Spektrum DX9. This evening I tried it outdoors and indoors. With the same...

Let me ask you a personal preference.... If you needed a 30a esc what would be a good better best..... I will look at the setup band might look to replace the ESC.... Thanks.

ZTW Spider OPTO 30A....I wasn't paying attention to the trims.... Should they all be zero or not negative or positive?

I put the endpoints to the recommended 125 for both throttle settings... Ran thru each esc connected to the Spektrum AR 9020 and they all took the settings put the endpoints back at 100 and tried to spin them up.... I'm just wondering how many people get the same number of tones at start up when...

Right now each end point is at 100. Can you give some clarity of your comment on opening up the endpoints during calibration.... Is this during the stick calibration or ESC calibration.... Thanks.

I went thru the ESC calibration again.... Connected the ESC directly to the throttle port on the Spektrum AR 9020, I get the one beep when the throttle is maxed when the throttle is dropped I get two beeps and a single beep.... When push up on the throttle the motor will spin up. All four did...

I sent the TX and RX and the SuperX to Drew at XA for him to get the settings correct.... I havent changed any of them... I will do another whole calibration again later today....

The LED is flashing is quick flashing green...I can cycle thru the three flight modes. Does it matter what mode the quad is in to arm the motors?

It does not appear I could arm the motors, the transmitter (Spektrum DX9) is on and binding with the receiver (Spektrum AR9020 with SATS). The LiPO is a 4S. Throttle is down at start up. As I mentioned, I went thru the throttle/stick calibration step by step and all the checkmarks were down...

Okay everyone... Ultimate thanks for the help! I have calibrated the ESC's and they came out fine from all accounts... They did a one beep and then a couple beeps....By the way the servo did work on the throttle channel on the AR 9020. Maybe a quick question.... The flight mode does switch and...

Never mind, I'm getting very close... Had a kink that I was plugging the servo into the bind port.... Dumb momennt

Thanks to the forum here for assisting me in the process to calibrate the quad I am building. Using the a HiTec HS-55 servo to see if there is signal from the Spektrum DX9 to the AR9020.... When the servo is connected to the throttle of the ar 9020 and the XA controller is powered up the servo...