Search results

Thanks Steve.... Iv sent 2 emails to smart-electronics in the last month and no replies.

I would like to buy a Smart OSD for Mk but they seem to be sold out everywhere ...Pm me if you might have one to sell.

I would like to buy a Smart OSD for Mk but they seem to be sold out everywhere ...Pm me if you might have one to sell.

Kloner , I decided to abandon my 5.8 gear and replace it with 2.4 for the Disco I’m building…I have been following your threads on FPV and looks like you have a good set up…Been doing lots of reading but still confused as to what products work well together. This is my short list …any...

Kloner thanks for the heads up on the Pixim bought it on your recommendation & saved lots of $$$ over the TBS 690. I do have another question since you must be the Guru of FBV quads... I need to get another VT what is the best vid transmitter and what frequency ? I have the immersion 600 setup...

Kloner,Is this the one you use http://www.camera2000.com/en/2-8mm-wide-view-ultra-wdr-690tvl-pixim-seawolf-sensor-chip-camera-osd.html

Wow the price is right...so do you do you need to do a firmware upgrade?

Kloner ..great build thread..One question I have is there any reason you went with the pixim 690 camera over the TBS 69 FPV? Just wondering Im getting ready to put my disco together and would like to get the best camera for the $$$$

Ken, good to hear the Ipower stand up to a good bump...I have been looking at them for my next quad, looks like the price is right for the quality... was wondering which motor size you are using on your Disco?

Thanks for the heads up LL...just placed an order...this is my 4th try hope it goes...

I have the same issues using the topflight MB.... same procedure but after hrs of messing about sanding, adding CA to the hub ect to get a perfect balance ,I found out that once balanced if the prop is turned on the shaft it will show out of balance !...thinking somethings up I then marked...

Jes... I have to say these look intriguing, I was wondering how far out the next build is? I would like to try one is it possible to pre-order?

Ken...I was wondering what kind of flight times your getting with the 5000s ?...Just got my qav500 together and with Nano-tec 5000s with 10" Graupners andnx 4008 620 kv motors on the first few flights I'm only getting about 7 1/2minuts.... I guess I was expecting at least 10 or more... I'm...

Looking for help ready to dump this thing into the bin...Not my first rodeo here but bought a GLB (Flycam) blackboard(blue) updated the firmware installed it on a 450 quad but all I get is the motors beeping continuously...the board flashes blue 3 times and then nothing.It won't arm and motors...

Thanks Ken ...just ordered 200lf don't know what the h**l I'm going to do with that much but the price is right....great find

Ken Great looking quad...just wondering where you found the spiral wire wrap in geen?....

Ken, Just sent you a pm but seems your box is full

Ken, Is the JR 921 the same as AR9000? If so from what I have read it should let me bind my older DSM2 satellites to the DX8 and get 8 channels...If this solves my problem I will gladly take it....let me how you would like to handle it.

Bart thanks for the info ...Just to clarify I m not having a problem getting the satellites to bind the problem is that I only get 6 channels to work. I did some digging and just a FYI for anyone considering the DX8 check out the threads below (page 11). It seems according to spectrum/horizon...

Interesting.... I had no problems SDB binding to my DX7, It bound and worked perfect the 1st time. From what I have read is that it won't bind correctly with the DX8 satellites evidently they are not compatible with the older DSM2. It looks like it is possible to bind the older (non DX8)...