Search results

A little update: - I received a replacement Radian from Tabb which ive wired up and programmed, worked as it should this time. - Got a good amount of work done on a charging case/station. Il post some pictures when its done. - Herkules boards ordered and paid for. - Remote switch for the...

Good point, i always assumed it would have worked at full voltage, it seems odd, because it works on up to a 14s battery, so how can it measure all the voltages if its coming though a regulator first?

Thanks alot for those diagrams. Ive found one from a NZ hobbyshop so I should have it in a few days to test which way works. Il have a Graupner telemetry unit, which i assume i would wire in after the switches. Is that what your meaning. Run the rx off a bec and then run the ys-x6 off of the...

BorisS, does this answere your question about wiring? http://www.rc-electronic.com/downloads/pdf/bedienungsanleitungen/Anleitung_SPS_RCS_Single_EN.pdf

Would a 2s have enough voltage at 6.6, to drop to 6v ok? I thought becs needed a bit more voltage for the drop?

I cant see the first link (session timed out) But its the safety power switch combined with the SPS-RCS, http://shop.rc-electronic.com/e-vendo.php?shop=k_emcotec_e&SessionId=&a=article&ProdNr=A72035&t=2263&c=2263&p=2263 Which just turns the safety power switch on and off via remote. I agree with...

Im going to be running a emcotec remote controlled power kill switch, the receiver needs its on battery to make this happen. Alough I just had a thought. I could just pull power off the main battery pack before it hits the emcotec unit. Can you see any issue with that?

Im going to power my receiver by a separate battery. Im unsure how large it needs to be and if lipo with a bec is the best way to go about it. Since its not going to be powering anything other than the receiver I cant imagine it would have to be a big battery. What size would you buy? Would you...

Did the copper shielding make any difference?

Thanks, ive already got a set of IBcrazy clover leafs and a patch for 1.3 and a helical for the 5.8. Havent changed over to the proper aerials yet. Im still having issues with the 1.3 not working on my Disco, but hopefully il get it sorted tomorrow.

Ive finished building the two ground station cases for video down link and fpv. 5.8 Downlink for camera operator: -Iftron Yellow Jacket Pro -Zippy 5000mah 4s battery hooked up to a voltage regulator dropping it down to 12v for the screen and Iftron. -PYLE 10.4" screen, nice and big to see whats...

would liquid tape work like goop?

The plan is to shoot fishing, shallow water just of the coast kinda stuff. Big sharks and Kingfish. Plus a lot of scenery. That will be the main purpose of the rig. https://www.youtube.com/watch?v=QD0ZLtU-Pzs But I plan on shooting some BMX for other projects, and what ever else needs to be...

Ive been having issues with one of my Freefly Radians. I couldn't get it into bootloader mode to update the firmware. After a small chat with Tabb, hes sending me out another unit. Great customer service right there. I spent the last week working slowly on the wiring of the Freefly gimbal...

Thanks, your correct, im in New Zealand. Il have to keep looking then, I was hoping it was another of your ebay finds. Any Chance you could get back to me about the Herk boards? Pretty keen to finalise them as my esc`s and get going on my skyjib build.

I need something similar to hold my patch antenna. Do you have a link to those? Your build looks excellent, very nice design.

Fair enough, it cant hurt by isolating them. If you didn't have the cs dampners, would you go to the trouble of adding dampeners to the board? Thanks for that.

Why do you need vibration dampening on the herk board? Does it help some how?

Do you have Andreas email?

Will The mounts be a straight swap upgrade for those who want them, or will we have to purchase them extra?