Search results

Anyone have any ideas....... These ESC's are making me crazy. :dejection: Every time I fly.... Im afraid Im gonna fall out of the sky. :butterfly: It kina looks like I will have to rip the guts out and start over. Any suggestions for reliable ESC's .

I have tried to get into programming many times. Not hard..... Connect and leave throttle high...... One beep at the beginning..... and no more. Im guessing SimonK Flashed and locked. Any ideas?

Yes..... I agree.... They don't say they are SimonK Flashed but the RC-Drones.com guy said they were..... What ever that means. I have fallen from the skies now twice while tuning the Naza for voltage protection with conservative numbers well over 3v per cell. One was my fault after flying on...

What does programming the ESC's to NiCad do..... Im assuming that NiCad can be drawn a lot lower than LiPo? I am sure the two near crashes I had were the ESC's. They are Maytech SimonK Flashed 40A-OPTO. Im running a DJI Naza and have the voltage monitoring set up to give me plenty of...

Hi there, Having a problem and need answers. :dejection: Have almost lost my aerial rig on a couple of occasion over your low voltage protection on the SimonK flashed 40A-OPTO's. My DJI Naza is fully capable of protection and voltage monitoring so I don't need double protection. On top of...

That SimonK low voltage protection has almost made me loose my copter now twice with my nex5 on board. I have protection on my Naza...... Would rather scrap a $50 battery that loose my ship. Anyone know how to re-flash these dam things to take it off? :apologetic:

You know how the dual lock has a little play in it? The super fine fibers seem to stop that and make the dual lock a little more solid. It seems to me that I had a lot less high frequency oscillation this way versus hard mounting the sensor. Was able to get the numbers a lot higher for...

Have you tried higher gains on the yaw? If you can't get them any higher without oscilating yourself into oblivion here is what I did and it worked great.... Sounds a little strange but......:pig:. Buy some of this 3M Dual Lock. Its like velcro but better and way more solid...

First minute of flight is over land......:nevreness:............ Last 3 minutes of flight is over land......:dejection:. Figure if something is going to happen its going to be sometime during that period.

Thanks Braaaa:livid:

What gimbal u using. Just setup one of those DYS 3 Axis Gimbals - Im impressed!

Very Nice!!:frog:

That looks like a couple things. It could be the sunlight going through the propellers casting a shadow on the lens causing lens flare that is modulated. The other possibility is it is frame vibration being transferred to the camera causing the lens flare to modulate. But it's one of the...

Enjoy the new footage from http://www.HawaiiAerialVideo.com :livid::

:upset: Went to update board as I have many times before....... And SHABANG!!!!:livid: NOTHING Board lights up sensor lights up USB shows connected (com 9) tried to roll back the driver to 2.2b2 AVRDUDER - response when old or new firmware is put in = avrdude: stk500_getsync(): not in...

4.0 Working good. So far... 4.0 is working good for me. Nice and stable. The Auto takeoff is ver cool. Just be aware of it at first. Ground effect hovering and descending has become easier as well.:livid:

Same issue.... 2.18 will not update to V4.0. Says mismatch and tells you to use 2.16 to update to 3.16????? Im confused now for sure!@!@

Anyone know of a multi-output BEC in the world. Would be great to have 4 adjustable outputs or more!!

BEC's probably the issue Well..... Didn't really ever find out what the absolute cause was... but everything pointed to the 5V line and the BEC's that I was running to reduce the voltages. I am running a 6S system and it seems that all the devices are rated for lower voltages. Possible causes...

Very Cool..... Just had a conversation with the designer of this system at Velodyne. Funny thing is... its the same company that's primary business is high end subwoofers for home theater. Very expensive at around 50K and not as accurate as it needs to be for surveying. Accuracy needs to be...