Search results

I have seen the question asked many times on here how to find the center of gravity on the WKM so I braved the winter weather and made a short video in the workshop on how I do it. There may be other ways, but this to me is the easiest and most accurate.

Well done, the first flight is always the best :)

Z axis is easy. Load up and hold your multi up as it would fly. Now turn it through 90° so that the booms are pointing up and down, left and right. Top is against your chest and landing gear away from you. Now try and balance it on your hands by holding it, say, under the booms. If it tries to...

Don't buy the highsight, total waste of money. Pain to assemble, flimsy as hell and sloppy servo arms. Regards, Gunter. Sent from my iPhone using Tapatalk

Also remember that the Naza has to have power before it will be seen by the pc, ie the power module needs I be connected to the battery and plugged into the Naza. It's not powered by the USB port. When you install the driver, that's all it does is to pop up a little black box and the driver is...

Dave, I've disabled manual because it's exactly that, too scary! Regards, Gunter. Sent from my iPhone using Tapatalk

On the Naza, when it goes into failsafe it automatically puts all sticks into the middle position, so it will hover until the battery is empty when it will land. Gunter.

Kopterworx in Europe had some last time I checked. I also got a notification that they were in stock with electricwingman, but that was a week or two ago and they seem to be out of stock again :( Gunter.

I have heard a couple of times that you can't take over control once you have hit fail safe. Is this true? I think it's vital that you should be able to flick it back into atti and carry on flying. Regards, Gunter. Sent from my iPhone using Tapatalk

Thanks Denny, I will see if I can get some smaller pulleys. Regards, Gunter. Sent from my iPhone using Tapatalk

Not sure Rich, but I am willing to swap it for an AV130, because it's too big for my setup! My partner in crime bought it second hand from a friend, it's hardly been used, so I'm not sure who made it...I'll find out. Gunter.

I am using the Hobbywing 40A esc's and they work a charm, no problems :) Gunter.

Denny, spot on mate, I'm impressed ;) Last night when testing it for the first time, I didn't spot that the pots grub screw wasn't done up tight. The pot was staying still while the gimbal was rotating...it shows what happens after consuming too much red wine :) I sorted it out this evening in...

Jack, The FC controls the angle of the camera to compensate for its own angle. When you tilt the camera, it tilts, and then the new angle is compensated...have a look at the short video I prepared earlier...

Thanks guys, I will try again a bit later. Regards, Gunter. Sent from my iPhone using Tapatalk

I have been trying to get this new gimbal working but with no luck! I have it hooked up to the WKM tilt and roll. When the heli tilts, the gimbal tilts, but totally randomly. I set the zero point, tilt the heli and then put it back on the table but the gimbal returns to a different position. No...

Kelly, you can assign 1 channel from your transmitter to control the tilt of the gimbal, so get a transmitter with a dial so you can use that to tilt the camera up and down. The Naza will have 2 outputs which control the gimbal tilt and roll. Regards, Gunter. Sent from my iPhone using Tapatalk

Kelly, the flight controller levels the camera gimbal for you. So if the heli tilts slightly to the left, it will automatically tilt the gimbal to the right by the same amount so it always stays level. The FC will also have 2 outputs for the gimbal which plug into the gimbal servos. Not all...

powerplay, hier habe ich eine kleine video gemacht von "home lock" es funktioniert echt gut :)

I did ask it, and it told me it wanted to be photographed by a friend...clear as day I tell you :) Never mind, I shall have to go and find my thinking cap again! Gunter.