Search results

What the #@*$ was he thinking, or not! We really don't need this kind of irresponsibility. I hope that those who don't know what their doing will think before acting and BE SAFE!!!! Learn to fly. Really stupid!

Yes, It looks the same. Newer version.

As gpforet said, Many of us have months into our equipment. If you take your time it will come to you. In the meantime of you want to learn to fly, an inexpensive way to do that is to get a RTF micro quad. I fly and octo and train with a Blade MQX. Great way to learn and hone your skills. If you...

Might want to make sure that motor shafts are straight. They wouldn't need to be off by much. That's if you don't find anything else wrong.

If your happy and it ain't broke don't fix it. If this set-up looks like the connectons diagram on the DJI site then I would assume that you are OK! Just my opinion.

If you haven't found a solution to the LED's yet try this. www.hobbyking.com. Search: UBEC 12v 4.5A. This will make it possible to connect the LED's to the PDB using a j-connector. There is a 2A UBEC, but with all the LED's you have it might be safer to go with the 4.5 it will run cooler, also I...

I wondered what was happening! It was strange to have that responce in the throttle. I don't think it's a bad thing, but I would rather be able to TURN IT OFF if I want to. And as said before, at least let us know ALL the things that have changed. It's a little nerve racking when you have a few...

I might be wrong, but when you calibrated the compass in the horizontal you had the airframe sitting on the skids, which was right, then you turned it which gave you calibration in the horizontal, but when you did the vertical you actually turned it horizontally while it was on it's side...

Have only flown 6 times with 5.24 and like it! I fly a CC Octo 1000. Never re-calabrated the compass, change Tx settings or gains. Wanted to see of there was going to be any difference. Haven't noticed any. RTH works great. Just lucky I guess. I did see somewhere, something about a LED defuser...

Thank's have to remember that one!

Excellant!!! Remember that heat concentrated in one spot is not good, as you noticed where you had contact, the short. The LED's will get quite warm if you don't get down to 12v. Might not be a problem, but over time could possibly cause fiber/resin breakdown on your booms. Congratulations...

I'm pretty sure that the only way to run a motor individually is to disconnect one of the leads +/_, and connect directly to it.

Great! Then have a good time and fly safe.

Let me start with the FACT that I'm in no way an authority on these builds. With that said, as to insulating you solder connections just be sure that if there is a chance that something might contact them you should prevent this from happening. There is some insulated tape that is thick and you...

Chances are you have a short. Look at your wires and see if the insulation on any of them looks damaged this might tell you which one got hot. The trouble with soldering your ESC's to the PDB is that if you need to test them individually you need to unsolder one wire. I don't think you damaged...

Make sure you set your values in the telemetry settings and activate the telemetry.

The BEC won't work. They top out at 7v. You can use a j-connector (male end without the sleeve), the pins will stick out and if you leave the center pin hole empty with + in one and - in the other this should plug into you balance connector. You'll have the - pin in the black wire port and the +...

I fold the tape over the leading edge. Never had an issue. I thinking of getting a dynamic balancer. I like the idea of balancing the motors also. At least I will have removed all the vibration I can.

I needed the same thing and found the same issue with the BEC's. What I did, thanks to an idea from my local shop, was to use a j-connector (male end) and made up the connector without the sleeve, so that the pins are showing. I put a pin at both ends with the middle one empty. One pin + the...

Don't know what else you can do at this time, but be patient and see what HF comes up with. They were good when I had an issue with the camera gimbal control board.