Search results

Maybe ive just got something wrong prop and motor wise... 4s 4000, 900 or 1000 kv on 10" props, im still not super clear on prop choice and motors. All i can think is the motor runs out of rpm and then drops causing the quad to do its rock n roll then causing the other motor to top out aswell...

Mine has been holding great since the update, got my tilt dialed in on my radio. Little tuning on the hexa and im a happy camper

Right on, yes they are identical brand new packs, meaaured resistance is equal

When i run my batteries parallel do I need to worry about an unequal discharge. Will one come to its low point before the other or do they pull pretty even? Thanks

Wierd man, i want them to work but everything ive tried i still get a crazy wobble thats completly uncontrollable, throw my dji esc in and all good, mind you it doesnt hover as nice... :( What batts u running. 3 or 4

I have now tried 2 different types of motors suppo 2814/8 1000kv and the mt2216/12 900kv, both went through the paces on graupner 10x5 props on 3s and 4s. low mid and high timing was used, all said and done and a couple prop break crashes i have come to accept that these ESc's wont work for me...

Got me some of those suppos, is this clamp on style prop mount trustworthy?? I will check proos b4 eacg flight

Sorry to thread jack but could you guys point me to this declination site and possibly tell me how to get somewhat a perfect alignment... Ed your 12 degrees offset but how do u figure, not by eye obviously

Awesome video meme

I had been after one for a few months and gave up, no reply from vendors or the man himself... opted for another controller that had me pretty satisifed, mind you im no professional lol but I am picky

I ran the 9's on 4s with my 550, i had a 4000 mah and xaircraft gimbal/gopro.. It was a bit of a struggle, it flew but hovered over mid stick

So far the gimbal has been great stabilization is spot on, lasting issue is managing a level horizon on roll and tilt... at least for me. I am happy with it though, as my first hoverfly product i'd use em again. ill try a couple different locations for mounting and hopefully by then there may be...

Im still having trouble with getting roll and tilt to hold a nice horizon, is it vibes? Possibly the mount location, where have u guys installed it on an av200? No 3rd

Mines motor 2, i tried different idle speeds and it didnt change anything. Hmm i just hope its not a sign of mid air failure

Ive done the checks of solder joints amd tried different esc/motor. What happens is at startup of my wkm one of the five motors spins or stutters. If i help it before starting by giving it a spin then starting it seems to perform fine, it started out of the blue and motors are about 1 hr of...

Kloner, u still running a naza? The vid where u say 500 watts was that manual

I have my esc's between the arms sandwiched in the plates, distro is a voltaire board with 14 guage copper for added beef. The voltair is rated for 75 i think, my logger today told me 85 amps on a hard climb out for 4 seconds, this did not have my gimbal or cam so im watching my distro...

Ok so i got it reflashed with .92 , setup quite nicely BUT im having an issue where once the gimbal pitches forward from level it activates the roll axis. roll is fine and pitching backwards is fine, just wierd i have tried a few things and cant figure it out... heres a vid, apologies on...

Thanks

Ive adjusted my hobbywing 30a funflys to mid timing. They are spinning my AXI 2814/22 w/ 14" apc sf props, after 10 minutes of mostly hovering and some pumping in between it comes down and the motors are warm to the touch and escs are aswell. Warmer than they have been yet not hot. What is a...