Search results

I noticed that this aft while browsing their site to. I went looking for a solo 5v camera there and couldn't find one. I agree, it's done. I will order a much more expensive 12v replacement shortly here. I'll order from a Canadian source so should get it much quicker.

ok, the ESC trick did not work. I powered it up by plugging the pack into it, then the Rx power/grnd to the camera. On a good note though, I found an A/V cable for my Canon camera. Cut the end of it off, hooked the yellow to yellow and white to black and IT WORKS!!! OMG... this was painful. I...

I'm not very good at this electrical stuff, as you could probably tell. I'm not confident enough to do what you are suggesting. I just happen to have a new 30 AMP ESC that came with the same order as this camera. Got it for the plane. How would I know if it puts out 5V or do they all put out 5V...

Hmm.. haven't tried 5v. I suppose it is very possible to send the wrong camera (ie; grabbed a 5v off the shelf instead of a 12v). I'll need to get some sort of step-down from 12v to 5v. I think I will try this. I can't stomach eBay/PayPal. They are only around $12 at NG Hobbies, but thanks for...

I am putting 12v to the camera. Yes, I am going to order a cable for the GoPro, as I don't have any plugs laying around like that.

That's fantastic... thank you! It's not the same board as mine, but close. I looked closely on mine and the back-side has no "Vo" marking. That tiny chip heats up SO fast and you can NOT touch it or it will literally burn you. I hooked up my GoPro Hero2 TV out to this Tx and I got sound, but...

I also moved the white wire on the harness so it matches up with the white wire coming off the transmitter. Did not make any difference.

Yes, I was browsing RCG, didn't find anything helpful. I realize now, it does have a mic. The blank wire came with it. Desc said "a spare to build your own or to use with a different camera/fpv". Yes, the wiring off the cam did come as plug 'n play. ok, I found a 2.5mm jack, plugged in the...

I don't think the camera has audio. I think that the white wire is being used as video and is connected to the yellow wire. There is no manual for the camera at HK

I agree, but I don't know the pinout.. I need to find a wire diagram for it then. There is nothing on the circuit board.

ok, I have checked and double-checked. I made a video as well. Maybe you can spot something?

Absolutely... I will double-check this again as well - hehe

Thank you for all the input. When I get home, I will check all the wiring. I'll also search RCG and see if I can find anything there.

I am in Canada. I have tried all the channels. I get static initially, then a message that indicates no signal. It's blue on my laptop and black on my TV (I think). Later, after work, I'll post a video, showing me hooking it all up. Maybe that will help more. I really appreciate the help folks.

Yes, 12v on Tx and Rx. Both powered up fine and both on the same channel

Hey all, So, I finally, after a little more than a month, received my order from HK: 900MHZ 1500mW Tx/Rx & 1/3-inch CCD Camera NTSC 520TVL http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=21326 Anxiously ran out and picked up two 3S 1300mAh batteries, charged them and...

Have you tried EC3's? I like those best because they are very easy to solder.

Nice. Thank you very much. What were you using all three positions for?

Well, actually, I did get it working and have flown a few times. I tried manual mode, but it's to sensitive. Does anyone know how to setup dual rates. I have the gear switch changing from Attitude mode to Manual mode, but need the dual rates setup so it's not so sensitive.

Ouch! Do you think the freezing cold had to do with the arm breaking? I bet it did. The frame is probably more resilient in the warm weather, like where it is from :)