Recent content by ryancanon

  1. R

    Aeronavics / Droidworx setting up Futaba 8fg for slow gimbal operating . .

    Right stick in dual operator mode, or another control for single op?
  2. R

    GH4 Rig Flight Times

    I'm pretty sold on GH4 for aerials, and am curious about how various builds stack wrt flight times. I'm especially interested in what kind of flight times S1000 and S900 users are seeing? Currently I have a Vulcan X8 w/ DJI Retracts, KDE 3520-400, Zenmuse GH4, and 15" Tarot CF Props. Using...
  3. R

    Sticks Calibration Issue, WKM

    Not sure why, but some combination of restarting the tx and controller fixed this issue...
  4. R

    Sticks Calibration Issue, WKM

    I'm having an issue setting up a WKM on a new X8. I have used this controller previously on a couple of different y6 configs, but did a factory reset to start with a clean slate. FW is 5.24, and I'm getting an error when trying to upgrade to 5.26. Receiver is Futaba R7008SB, and WKM is in...
  5. R

    Two Brand New Gens Tattu 10,000 mAh 6S LiPo

    Yes, $400 is for both batteries. As Kloner said, these are incorrectly labeled to indicate that they are under the 100 wh limit. I am told that the correct 10,000 mah label is underneath this one.
  6. R

    8x KDE Triple Prop Adapters V2 with DJI 1552 Blades

    4 sets (4x LH, 4x RH) KDE Triple Propeller Adapters with DJI 1552 propellers. Also included are the original DJI 2 blade adapters. These are new, and have never been flown. These are the V2 triple adapter, redesigned for broad motor compatibility. There are holes for M3 x 12mm dual-thread...
  7. R

    4 Sets APC 16x5.5 MR and MRP Props, Never Used

    4 Sets of APC 16x5.5 MR and MRP Props, New. 6 of these are in unopened packaging, and two have been opened to test for interference with retractable landing gear, but never flown. $35. Shipping included within the Continental US. Shipping from Fort Lauderdale, FL. Buyer pays paypal fees. I...
  8. R

    5 Sets T-Motor 16x5.4 Carbon Fiber Props

    5 Sets of T-Motor 16x5.4 CF Props. Four of these are in like new condition, but one set has some slight wear marks on the tips. I purchased them second hand for a Vulcan Heavy Lift build (also listed), but have not used them. $350, including shipping via UPS Ground within the continental US...
  9. R

    One Brand New Gens Tattu 16,000 mAh 6s LiPo

    New, never used Gens Tattu 16,000 mAh 6S LiPo Battery Purchased for a heavy lift build, but never flown. EC5 Battery Connector Installed. $315, UPS Ground Shipping included within the continental US. Shipping from Fort Lauderdale, FL. Buyer pays paypal fees. I will not be able to ship between...
  10. R

    Two Brand New Gens Tattu 10,000 mAh 6S LiPo

    New, never flown. I've had these for about a month. These were purchased for a heavy lift project that I'm no longer interested in pursuing. One battery has an EC5 connector installed, and the other is unterminated. $400. UPS Ground Shipping included within the continental US. Shipping from...
  11. R

    ARF - Heavy Lift Folding Vulcan X8 with KDE 3520-400 Motors

    Heavy Lift Build in Progress, ideal for a DSLR or GH4 and Movi M5. All of these parts are new, and have never been flown. The frame is built, and power system wired in. Just add receiver, flight controller, propellers, battery, and gimbal. I have some of the other parts planned for this build...
  12. R

    SBUS receiver with A2 - R7008SB with Futaba 14CG

    Thanks... My plan was to use an eFuel Gauge alongside the A2.
  13. R

    SBUS receiver with A2 - R7008SB with Futaba 14CG

    I don't have any setup advice, but am curious. What functionality/benefit is gained using the r7008sb rx alongside A2, as opposed to just using the integrated rx?
  14. R

    Help in deciding what to build for 2nd multi-rotor.

    You could always sell me your pocket cam and use that money for a very nice flight controller... :) Sent from my iPad using Tapatalk HD
Top