Recent content by Risen91

I'm no so sure its sensor drift, it works flawlessly when not connected to the receiver and when motors are on, if it was a chip fault it would be constant. It really seems like its receiving some sort of unwanted signal from the receiver but I don't know why or how to check it. Also as Old Man...

So with the WiFi off it still has the same effect. I really have no idea whats causing this :(

Checked the voltage before and after and it stays pretty much stable both on and off, there is no fluctuation that would cause the movement. It has to be there is some signal going through the receiver that is affecting it, this has me wondering if the wifi signal from the other room would be...

Considering how well it moves when not connected to the RX (and also when the motors are on) I would guess that the PID's are perfect how they are. I was thinking the same thing about the prop injury and that's mainly what worries me about this. I will check the voltage later today to see what...

Yea I know :) finally got the motors updated as well a few hours ago. Still getting the same problem though, when the motors are not throttled up the gimbal moves on its own, as soon as throttle is applied, it works perfectly and also I can control it using the transmitter. It could be worse I...

Ok! so an update... I finally managed to get the firmware update to V1.5 Hurrah! However, now the motors wont update. I have also found out that as soon as I apply throttle to the motors the gimbal performs perfectly, stays steady and only moves up/down when I tell it to. It's only when the...

Yea I have done that, the guide says to connect the gimbal, open com port, select update, start update and then power up the gimbal, that's what the guy in the Youtube video did and it worked perfectly for him. The latest version is V1.5 and that's the one I'm trying to upload onto the gimbal.

I have tried turning the transmitter on and it does slowly roll when I move the stick position, however it still slowly moves around on its own. I have tried to update the firmware but am having issues with uploading it. After spending an entire day trying to get the computer to even detect the...

Alright I need help, I have a Tarot 2d gimbal that when disconnected from the Rx (frsky x8r) works flawless (stays center and reacts when moved) but as soon as I connect it to the Rx it starts moving on its own, not shaking, but just slowly moving up and down. How is connecting it to the Rx...

So finally everything is here! started the process of working out how all the wires go together now and I think so far its going good, just have a few questions. Not entirely sure how the flight controller actually gets power, as far as I can see (not good at electronics at all) the way it gets...

Just got my LiPo batteries today and it says they should be charged at 14.8V on the battery but they are actually charged at 15.22V, is this a problem? I ordered from HobbyKing. I think I heard somewhere that 3.8V per cell is optimal for storage (15.2V total)? Also is the fridge in a LiPo-Safe...

Luckily I think I have managed to snag some on ebay before they go completely, there is 3 sellers on the .com (pretty good price) and one on the .co.uk (but costs a lot), they all have limited stock though.

Not sure, but every page on their website has "Sorry, no found no data" and every other company that stocks them is out of stock and have said they are not sure when they will be shipping again. I don't think they are currently shipping any motors.

So for some reason Sunnysky isnt selling the motors right now (not sure if they will at a later date or stopped all together). Is there any other motor makes you can recommend? I have already got my props (12x4.5) so I kinda need to build it around them. This sucks -.-

Although it hasn't arrived (just starting my first build also) I got recommended the FrSky Taranis X9D. Although a little more expensive it has a lot of good reviews and I see many videos of people using it. Good luck with the build whatever you choose :)