Recent content by kokamintti

Hi Just thought sharing this. It was a quite unique moment for us to film the morning mist in Helsinki's Old City rapids. Shot with GoPro 3, DIY quad WKM and DYS 3axis gimbal. Thanks for watching!

Yep. The dealer just asked me to send the IMU and PMU back for replacement. I'll go that way happily. We'll see how it goes. I'll post the result after replacement and tests. Thank you, Ben, for your support!

Well that would be understandable if we had exactly the same setup. And after importing the "good" settings file they ask to reset the FC. This would mean that I need to set the correct configuration for my setup again. Unless there's some magic going on with the import/export I don't undestand...

Ben, Good to know there's someone to back me up if needed. I got answer from my dealer Eladio from ElectronicaRC and he was very willing to be in contact with his DJI support contacts. I'll be able to replace the needed parts for warranty. But first I think we must identify how we know should...

Thanks! How can you (or can you?) tell what batch the units are? Do you have any information on what batch is your FC, PMU and IMU? The old and the new ones. I contacted my dealer and DJI as well. -mika

Uuh. Its -5 degrees out there. I think I'd have to be really desperate to go out there butt naked. But if that's really is what it takes I'd do it without hesitation. I'll try to get the gps declination correction sorted out this night. That's the last thing left to tune that I can think of...

This has been very intresting to read this thread sinve I have exactly THE SAME PROBLEM! I fly homebuilt Y6 with avrotos, APC 1238SF on top and 1260EP on bottom, 4S 5000mah or 8000mah. AUW 4,2kg with canon 550D and a crappy gimbal. I have iOSD (mark I) and 5,8ghz 200mw vtx and a ccd cam for fpv...

I'm going with two Orange receivers in satellite mode to provide up to 14 channels. I've fitted the antennas in a track I've made to the top cover of the box. All the electronics boxed. Still very easy access if necessary. And here's the bastard at the moment. His name is Jake.

Ready for ESCs The two front arms lock with a safety pin. ESCs in place. HF Pro board will sit on a bottom plate of a polycarbonate box Board installed. Only one red cable going into the board from the ESCs. I might ad a BEC later to do the job. In front is a modified LC filter from...

Hello guys! Check out my build log here, if you wanna see how the prize motors are being deployed. Thank you Monto RC and Multirotor Forums! -Mika

The opposite motor plate glued I had to reinforce the center plates with some aluminium profiles. I might have to redesign the center plates. I think they are too weak, only 1,5mm cf. But we'll see that after the first flights. Motor to motor about 70cm. I made one spare arm as well...

Hello all of you out there! I was the lucky one to win the "Beyond the Hover" -contest organized by Multirotor Forums and Monto RC. Prize was six Avroto 2814 short shaft motors. EDIT: original thread...

WHOOOOOOOH! JEA! Thank you everyone and especially Mr. Bartman! I'm a very lucky man at the moment. And to the question about Kokamintti I think I'll never be able to explain that in english but it sure has nothing to do with any narcotics. :) Thanks to sponsors as well. -Mika

Thank you all for the positive feedback. It really was fun to try this and can't wait for the woting to start! Keep it in the air! -Mika

Hi there! I'm pretty new to multirotors, only been flying for about a month. But I have a project of flying a DSLR in near future, like many of us I think. So I decided to give it a shot, though I know, that I really can't compete with the Experienced and Skilled. What the heck, it was fun...