Recent content by EagleEye

  1. E

    DJI F550 w/NAZA and GPS-JITTERY GIMBAL SERVOS-UGH!!!!!!!!!!!!!

    Hey, which gimbal are you using? I use the HS-65HB, too, and theres no major jittering it all. If I take a close look at the camera when moving the Quadro in my hand I can see some jittering because my servos run at 50 Hz. But it's not noticeable on the video. Have you tried running the...
  2. E

    Naza GPS unit replaceable with common USB-GPS?

    I'm just curious: Did anyone try to replace the original DJI GPS-unit for the Naza with a non-DJI GPS module? Or does anyone have a clue if it could be possible? I've got two different GPS modules, used on laptop with usb connection, lying around. Would save some money to spend on batteries...
  3. E

    A bit of desperation: Naza F450 motors won't start with CSC

    I finally got it! Thank you all for contributing to this thread and helping a fellow multirotor-addict not loose his patience =) For anyone that suffers the same problems, this is what I've done to make it finally work (I will describe the whole way since I can't say what made the...
  4. E

    A bit of desperation: Naza F450 motors won't start with CSC

    Almost forgot: Does anyone of you still have the Naza software assistant 1.2? There are several guys out there that had the same problem as I do right after they updated to 1.6 / 1.8, so I'd really like to downgrade my Naza. But the 1.2 assistant is no longer available at DJI's website.
  5. E

    A bit of desperation: Naza F450 motors won't start with CSC

    Thanks Phil, I will read it carefully.
  6. E

    A bit of desperation: Naza F450 motors won't start with CSC

    I guess I'll get some minutes of sleep (worked the early shift on a radio station) and then tear the whole thing apart, do every step again, reset the Naza and see what will happen. :-/
  7. E

    A bit of desperation: Naza F450 motors won't start with CSC

    3S 2200mah. Alternatively I could try a 4s 3300.
  8. E

    A bit of desperation: Naza F450 motors won't start with CSC

    Sorry for the late reply. The Naza glows red (no flashing).
  9. E

    A bit of desperation: Naza F450 motors won't start with CSC

    The left stick was bottom right, the right stick bottom left.
  10. E

    A bit of desperation: Naza F450 motors won't start with CSC

    I remember resetting works with connecting F1 and F2 with a servo cable, am I right? Don't want to burn this thing.
  11. E

    A bit of desperation: Naza F450 motors won't start with CSC

    Yes, I am. Is there any way the software tells me that writing was successful?
  12. E

    A bit of desperation: Naza F450 motors won't start with CSC

    It was a set with the F450 frame from firstpersonview.co.uk, already contacted their support. I'm really frustrated because it doesn't work while everything is set up in a way that works for others.
  13. E

    A bit of desperation: Naza F450 motors won't start with CSC

    And here it is: http://www.youtube.com/watch?v=j1znf3lDDH0
  14. E

    A bit of desperation: Naza F450 motors won't start with CSC

    A video is on the way. Firmware is 2.02. At least three CSC are dead on, on one try on the video I don't know if it was me (one-handed CSC while filming wasn't that easy) or the radio. D/R is 100 %.
  15. E

    A bit of desperation: Naza F450 motors won't start with CSC

    Here we go, that is the Naza connected to the OrangeRX starting up in ATTI mode. http://www.youtube.com/watch?v=aOrBMdTerGY And this is what it looks like in manual mode: http://www.youtube.com/watch?v=MKNjCDOIt1s
See more
Top