Recent content by Bob002

I do not. Tx is a Walkera Devo7. Rx is a Walkera Rx701, I believe.

I've posted about this on several other places to no avail. Long story short, my Naza-M v2 is not holding my Tx calibration settings. Get an error code 29 when I hook it up. Takes 2-3 times before actually recognizes the stick signal properly (but only on particular stick). Seems to only hold it...

Took this last night. First "real" flight after my crash. I know I need to A) edit my field of view and B) figured out how I should have approached. But, I was mostly doing this to try out the gimbal and tilt feature.

after some messing around, i really think it has something to do with the tilt. I've seen about 18 different ways to hook this up. Currently I have the supplied cord to CTR on the control board. Then on my receiver, I have the red wire (from where it splits into 3) into Aux2. I suppose I could...

So, finally got ends on the power end of the Tarot. Hooked it to the comp, calibrated. Flashed the settings. Tested it. Seemed to work. Hooked it up to receiver for tilt (tested and worked), and it works for a minute or so. Then it starts spazzing out. It tilts one way, then the other...

Having an issue that I can't quite get figured out. Earlier, things were working, save that I had a wire on the Naza-M switched and didn't know it. Thought it was not properly calibrating the throttle range on the ESCs. Went back, removed everything from the receiver (Walkera Devention 7)...

Here is my 2nd video I did. Was just doing a quick show and test of the FPV, so that's why the rotor wash. I don't have my gimbal hooked up, so that's the reason for the rotors being in there in the first place.

Only think I could think is down & left and down & right. That's how I arm my Storm.

http://imgur.com/a/N3XQD Here are some images for you to peruse. Basically, the pin is held by a set screw (what I'm seeing in several, after looking closer). Long story short, I think I need to reset them different than how I did it, as it result in this:

Figured out what happened. Only going off these motors, as they are the first i've dealt with. It's not attached to the bell. Apparently, they use a set pin to hold everythign in place. When it flipped over in the grass, something must have happened and the set pin came lose. On my way out...

It occurred to me there might not be enough information. These are the motors that came on it. The pin isn't attached to anything that I can tell (unless it's internal). I really can't tell what the issue is, other than it wants to separate after a minute or so...

Not sure exactly what happened. Went to an empty field and long story short the grass was too long. The feet on the Storm Drone 6 got caught and it flipped. Moved across the street to an empty lot, flew it, tested return to home, all was well. Went to mother-in-law's house to pick a table up...

Cannot find what size these screws are. First is labeled M2x24mm and holds the GoPro in. Thinking 1.3mm but want to confirm. Second is the 4 that holds the board in and are labeled M2x6mm. They look to be the same size, but this is driving me crazy. I don't want to buy 40 different fasteners...

Received my Storm Drone 6 from Helipal (which, I'm totally amazed between them and DHL) this evening. Had a few bumps along the way, but overall it's been a positive experience. Took it on my first flight and it was amazing. Smooth. Flew great with 0 problems. No pictures because it was dark...

After some back and forth, I went ahead and purchased the Storm 6. I think overall I will be happy for the purposes I'll be using it for for the time being with the intention of building an F550 in the future should things go well. I simply wanted something that I could get in short time as I'm...